power to manual steering - The 1947 - Present Chevrolet & GMC Truck Message Board Network

rusty76 · 04-28-2013, 06:55 PM

I did do a search and well not the info I was looking for. At the moment my ole truck has power steering. It's been fine but now I'm getting ready for a tear down I need some info. I know that to go from power steering to manual I need the box and pitman arm. But what else do I need? Are the boxes same length and mount the same? Any variations in the center link? Also will the stock splines on the column to rag joint to box work? I've seen some companies list the boxes as having different splines than that of the power steering boxes. Any help greatly appreciated. Thanks.

INSIDIOUS '86 · 04-28-2013, 10:09 PM

Just cut the belt and run a resivior for lubrication. These boxes are easy enough to turn as is. Done mine like such for 4 yrs.
Posted via Mobile Device

KQQL IT · 04-28-2013, 10:34 PM

Manual boxes are out there.
Just have to look.
Mine was bolt in.
The manual intermediate shaft from power box different
Posted via Mobile Device

rusty76 · 04-29-2013, 06:33 AM

Quote:

Originally Posted by KQQL IT

Manual boxes are out there.
Just have to look.
Mine was bolt in.
The manual intermediate shaft from power box different
Posted via Mobile Device

What do you mean by manual intermediate shaft is different from the power boxes? Thanks for the help folks.

SSC's76 · 04-29-2013, 12:22 PM

Depends on what you get the shafts should be the same. I'm fairly certain the pitman arms are interchangeable as well. The only time I've ran into an issue going the opposite route of course is with a rear steer system in the older cars. You can use either box but if using a power box or manual box made for front steer linkage the pitman arms are different diameter
Posted via Mobile Device

lilpoindexter · 04-28-2013, 11:44 PM

I went to power from manual in my 78 C10. I used the corresponding pitman arms, but the boxes bolted up to the frame the same. The linkage is all the same. I really hated parking that old beast without power steering. I don't remember if the rag joint was different, but I don't think it was.

cory d · 04-28-2013, 11:51 PM

i looped the lines on my box. i dont even have the power steering pump on it anymore. i have strong arms from riding bmx bikes but my cousin drove it just fine. once he realized he cant turn the wheel when the truck isnt rolling

KQQL IT · 04-29-2013, 12:43 PM

The output shaft is smaller by a good bit on the manual box
Posted via Mobile Device
http://www.google.com/custom?domains...D%3A1%3B&hl=en

rusty76 · 04-29-2013, 04:01 PM

Thanks fellas. I kinda thought that they weren't completely interchangeable but close. Thanks again.

04-28-2013, 06:55 PM	#1
rusty76 Registered User Join Date: Sep 2012 Location: Midway, NC Posts: 3,275	power to manual steering I did do a search and well not the info I was looking for. At the moment my ole truck has power steering. It's been fine but now I'm getting ready for a tear down I need some info. I know that to go from power steering to manual I need the box and pitman arm. But what else do I need? Are the boxes same length and mount the same? Any variations in the center link? Also will the stock splines on the column to rag joint to box work? I've seen some companies list the boxes as having different splines than that of the power steering boxes. Any help greatly appreciated. Thanks. __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=581873 The low buck build threads. Check'em out! http://67-72chevytrucks.com/vboard/s...d.php?t=666022 My build thread Crossmembers CC

04-28-2013, 10:09 PM	#2
INSIDIOUS '86 Registered User Join Date: Jul 2009 Location: washington Posts: 4,178	Re: power to manual steering Just cut the belt and run a resivior for lubrication. These boxes are easy enough to turn as is. Done mine like such for 4 yrs. Posted via Mobile Device __________________ 377 sbc thumpr cam autogear m23 muncie 3:73 Detroit trutrac 3''spintech prostreet mufflers xpipe 1 3/4 headers build thread !http://67-72chevytrucks.com/vboard/s...d.php?t=577217 Iroc gauge threadhttp://67-72chevytrucks.com/vboard/s...d.php?t=554511

04-28-2013, 10:34 PM	#3
KQQL IT At the body shop. Join Date: Aug 2009 Location: Land of fruits and nuts. Posts: 5,257	Re: power to manual steering Manual boxes are out there. Just have to look. Mine was bolt in. The manual intermediate shaft from power box different Posted via Mobile Device __________________ " That didnt make it any newer " " Dont antique the equipment "

04-29-2013, 12:22 PM	#5
SSC's76 No No Join Date: Jun 2005 Location: Pueblo Colorado Posts: 1,781	Re: power to manual steering Depends on what you get the shafts should be the same. I'm fairly certain the pitman arms are interchangeable as well. The only time I've ran into an issue going the opposite route of course is with a rear steer system in the older cars. You can use either box but if using a power box or manual box made for front steer linkage the pitman arms are different diameter Posted via Mobile Device __________________ 1976 Custom Deluxe SWB Med FMB.3/4 Drop. Gen VI 454, Muncie HD 3 speed With Modified OE Hurst Shifter, 3.73 12 bolt, GMPP HO roller cam, Hooker headers, Performer intake with modified Q-jet, Accel distributor. Best 1/4 12.3 @108. Funnest run 19.84 @88 full 1/4 mile burn out. 1997 K1500 ext cab 5.7 stock except muffler

04-28-2013, 11:44 PM	#6
lilpoindexter Registered User Join Date: Sep 2010 Location: los angeles Posts: 1,134	Re: power to manual steering I went to power from manual in my 78 C10. I used the corresponding pitman arms, but the boxes bolted up to the frame the same. The linkage is all the same. I really hated parking that old beast without power steering. I don't remember if the rag joint was different, but I don't think it was.

04-28-2013, 11:51 PM	#7
cory d Registered User Join Date: Dec 2011 Location: Arlington WA Posts: 1,728	Re: power to manual steering i looped the lines on my box. i dont even have the power steering pump on it anymore. i have strong arms from riding bmx bikes but my cousin drove it just fine. once he realized he cant turn the wheel when the truck isnt rolling __________________ GMC C15 355 SM465 3.73 80 C10 cruiser build thread 79 short stepside crew cab. big and ugly. build thread

04-29-2013, 12:43 PM	#8
KQQL IT At the body shop. Join Date: Aug 2009 Location: Land of fruits and nuts. Posts: 5,257	Re: power to manual steering The output shaft is smaller by a good bit on the manual box Posted via Mobile Device http://www.google.com/custom?domains...D%3A1%3B&hl=en __________________ " That didnt make it any newer " " Dont antique the equipment "

04-29-2013, 04:01 PM	#9
rusty76 Registered User Join Date: Sep 2012 Location: Midway, NC Posts: 3,275	Re: power to manual steering Thanks fellas. I kinda thought that they weren't completely interchangeable but close. Thanks again. __________________ http://67-72chevytrucks.com/vboard/s...d.php?t=581873 The low buck build threads. Check'em out! http://67-72chevytrucks.com/vboard/s...d.php?t=666022 My build thread Crossmembers CC



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.