|
|
|
06-25-2013, 07:17 PM
|
#1 |
|
Registered User
Join Date: Oct 2009
Location: Austin, Texas
Posts: 241
|
Ignition Bezel Tool
Can any of you provide info/part number of the tool used to install the ignition switch bezel on my '64 GMC with stock ignition switch and stock bezel?
|
|
|
|
06-25-2013, 08:11 PM
|
#2 |
|
Registered User
Join Date: Oct 2009
Location: Austin, Texas
Posts: 241
|
Re: Ignition Bezel Tool
There are three slots along the outermost edge of the bezel and they are approx 1 1/4" - 1 5/16" apart from each other.
|
|
|
|
|
06-27-2013, 08:23 PM
|
#3 | |
|
Registered User
Join Date: Feb 2009
Location: southeasternfoothillsofusa
Posts: 1,557
|
Re: Ignition Bezel Tool
Quote:
Sam |
|
|
|
|
|
06-27-2013, 09:28 PM
|
#4 |
|
Registered User
Join Date: Oct 2009
Location: Austin, Texas
Posts: 241
|
Re: Ignition Bezel Tool
Sam: Thanks for the reply. I used an old fork and removed one tine then adjusted the remaining three tines to make a perfect tool for the job. Saved $20 and didn't scratch the new dash paint.
|
|
|
|
|
06-28-2013, 07:17 AM
|
#5 |
|
Registered User
Join Date: Feb 2009
Location: southeasternfoothillsofusa
Posts: 1,557
|
Re: Ignition Bezel Tool
Just wait 'til we tell your wife what went with her favorite old fork from Aunt Minnie'!
Sam |
|
|
|
|
06-29-2013, 10:31 AM
|
#6 |
|
Chevy addict
Join Date: May 2012
Location: Iron Ridge, WI
Posts: 1,085
|
Re: Ignition Bezel Tool
Used an old socket, forget what size and ground it down till I had three points to fit in the slots.
|
|
|
|
|
06-29-2013, 11:00 AM
|
#7 |
|
Registered User
 
Join Date: Mar 2012
Location: Pueblo West, Colorado
Posts: 430
|
Re: Ignition Bezel Tool
Here's the tool at classic industries. Sure others have it also.
 Posted via Mobile Device Posted via Mobile Device
__________________
Sold the 63 and have a 68 now. 63  SWB C10 LT1/4L60E, PS, PB, Disk Brakes, CPP 4" drop coil rear, 2.5" drop spindle w/ 1" drop coil. slotted rotors, front and rear sway bars. 18"x8" Cragar SS w/ 245/45R18 http://67-72chevytrucks.com/vboard/s...d.php?t=544174 |
|
|
|
|
06-30-2013, 12:20 PM
|
#8 |
|
Senior Enthusiast
Join Date: Feb 2007
Location: Spokane Valley, WA
Posts: 8,356
|
Re: Ignition Bezel Tool
The authentic original GM tool should be shown in the correct year Truck Shop Manual. It is found under Special Tools, Electrical like this one from the 1960 Chevy manual. For this year the correct tool is number “J-7726 Ignition Switch Nut Remover and Installer”.
This is the only year manual I have. Perhaps another forum member can scan the similar page from a later manual and post it up. If the correct part number was known, it might lead to finding one on Ebay or elsewhere. 
__________________
My Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=444502 |
|
|
|
 |
| Bookmarks |
|
|
Hybrid Mode
