LS3 heads versus LS6 heads? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

vannatta20 · 08-04-2013, 08:03 PM

I have a 6.0 lq4 engine and came across a set of Ls3 heads with the truck intake for a great price. I also just bought a set of LS6 799 heads for it. I dont know which set to install now.....The ls6 heads are low mileage but the LS3 heads have about 190000 miles on them. I can get a new LS3 intake for 200$ or use the truck intake. Its a daily driver and wanted the LS6 heads for increased compression and torque. The LS3 make a lot more horsepower though...I can sell the LS3 heads easily and buy a nice intake for the LS6 heads to dress up the engine and get a bit more power. What should I do??

69CST6.0 · 08-04-2013, 08:43 PM

Depends on your budget which way you go. The ls3 heads will give you more power but you will need a rectangular port intake and a aftermarket throttle body if going dbc. Also the cam splits are a lot more exhaust biased for the ls3 heads. BTW 799 heads are 5.3l truck heads, They are the same as the 243 ls6 heads minus the sodium filled valves.

Super73 · 08-10-2013, 12:30 PM

Quote:

Originally Posted by 69CST6.0

Depends on your budget which way you go. The ls3 heads will give you more power but you will need a rectangular port intake and a aftermarket throttle body if going dbc. Also the cam splits are a lot more exhaust biased for the ls3 heads. BTW 799 heads are 5.3l truck heads, They are the same as the 243 ls6 heads minus the sodium filled valves.

Be careful what you say as "truck heads" can be very confusing. Early 5.3's did not wear either version of the LS6 castings.
Posted via Mobile Device

Jon01 · 08-05-2013, 10:35 AM

On a stock displacement lq4 I'd just put the cathedral ports on it.

Blackpony · 08-05-2013, 11:47 PM

The 799 heads have a larger combustion chamber that will keep your cr low. I would do the ls3 if your budget will allow to property set it up.
Posted via Mobile Device

vannatta20 · 08-06-2013, 05:55 AM

799 have the smallest chamber out of the 3 pairs of heads I have now. 317s and 823 heads are about the same at 70cc. 799 are 64cc so they will bump up compression

Blackpony · 08-06-2013, 10:05 PM

Quote:

Originally Posted by vannatta20

799 have the smallest chamber out of the 3 pairs of heads I have now. 317s and 823 heads are about the same at 70cc. 799 are 64cc so they will bump up compression

My bad you are correct. I was thinking about the 317 truck heads. All these different casting numbers get me confused sometimes.. haha I am use to building sbf's..

68GMCCustom · 08-07-2013, 07:41 PM

The genIV 6.0L LY6 motors come with L92/LS3 style heads from the factory and make great power with just a cam swap.

vannatta20 · 08-10-2013, 04:58 AM

Well i ended up selling the LS3 heads so ill see how the LS6 heads do with a moderate cam in my 6.0. I have a 6.0 with LS3 heads on my 68 firebird and ill see how this combo compares.

smoky02 · 09-02-2013, 06:17 AM

vannatta I did the LS3 heads and intake on my LQ4 and love it.

Kainedogg · 09-04-2013, 05:35 PM

I was thinking of doing the LS3 heads my self but for the added cost and the hp increase in the higher rpm range, it just didn't make sense for my truck. If under the other hand if I was building a 408" stroker then the best bang for the buck heads would be the LS3's all day, especially with the valves now unshrouded. On a different note I have driven a buddy's truck with the LY6, cam and tune and it felt as quick, but not staggeringly quicker than a mutual friends older LQ4 with shaved iron heads and very small cam.

08-04-2013, 08:03 PM	#1
vannatta20 Registered User Join Date: Oct 2011 Location: Las Vegas, NV Posts: 291	LS3 heads versus LS6 heads? I have a 6.0 lq4 engine and came across a set of Ls3 heads with the truck intake for a great price. I also just bought a set of LS6 799 heads for it. I dont know which set to install now.....The ls6 heads are low mileage but the LS3 heads have about 190000 miles on them. I can get a new LS3 intake for 200$ or use the truck intake. Its a daily driver and wanted the LS6 heads for increased compression and torque. The LS3 make a lot more horsepower though...I can sell the LS3 heads easily and buy a nice intake for the LS6 heads to dress up the engine and get a bit more power. What should I do??

08-04-2013, 08:43 PM	#2
69CST6.0 Registered User Join Date: May 2012 Location: Ft Stewart, GA Posts: 37	Re: LS3 heads versus LS6 heads? Depends on your budget which way you go. The ls3 heads will give you more power but you will need a rectangular port intake and a aftermarket throttle body if going dbc. Also the cam splits are a lot more exhaust biased for the ls3 heads. BTW 799 heads are 5.3l truck heads, They are the same as the 243 ls6 heads minus the sodium filled valves.

08-05-2013, 10:35 AM	#4
Jon01 Registered User Join Date: Nov 2012 Location: West Des Moines, Iowa Posts: 450	Re: LS3 heads versus LS6 heads? On a stock displacement lq4 I'd just put the cathedral ports on it.

08-05-2013, 11:47 PM	#5
Blackpony Registered User Join Date: Feb 2013 Location: Aubrey, TX Posts: 308	Re: LS3 heads versus LS6 heads? The 799 heads have a larger combustion chamber that will keep your cr low. I would do the ls3 if your budget will allow to property set it up. Posted via Mobile Device

08-06-2013, 05:55 AM	#6
vannatta20 Registered User Join Date: Oct 2011 Location: Las Vegas, NV Posts: 291	Re: LS3 heads versus LS6 heads? 799 have the smallest chamber out of the 3 pairs of heads I have now. 317s and 823 heads are about the same at 70cc. 799 are 64cc so they will bump up compression

08-07-2013, 07:41 PM	#8
68GMCCustom Truck and auto performance nut Join Date: Feb 2007 Location: McKinney,Texas Posts: 3,848	Re: LS3 heads versus LS6 heads? The genIV 6.0L LY6 motors come with L92/LS3 style heads from the factory and make great power with just a cam swap. __________________ Kurt - '68 GMC short step - NIB '09 LY6 6.0L crate motor w/mods, NIB '12 crate 4L85e w/billet 3k stall Circle D, 3.73 posi 12 bolt, DynaTech f-swap headers, 3/4 drop, handling mods, etc. - my toy '72 Chevy LWB C-10 Highlander - 350/350 ps/pb/tilt/ac - not original but close '06 Chevy TrailBlazerSS - LS2/4L70e - little black hot rod SUV - my DD '18 Kia Sorento - wife's econo-driver '95 Chevy S10 - reg cab shortbed, LS, 4.3, auto... my '68's powertrain and chassis build -links broken A surprise phase - carb to efi -links broken

08-10-2013, 04:58 AM	#9
vannatta20 Registered User Join Date: Oct 2011 Location: Las Vegas, NV Posts: 291	Re: LS3 heads versus LS6 heads? Well i ended up selling the LS3 heads so ill see how the LS6 heads do with a moderate cam in my 6.0. I have a 6.0 with LS3 heads on my 68 firebird and ill see how this combo compares.

09-02-2013, 06:17 AM	#10
smoky02 Registered User Join Date: Oct 2003 Location: Sunny, Florida, some might call it South Alabama Posts: 834	Re: LS3 heads versus LS6 heads? vannatta I did the LS3 heads and intake on my LQ4 and love it. __________________ Just sold my C10...sad day... Looking for a 1972 Blazer to hopefully fill the hole in my heart.

09-04-2013, 05:35 PM	#11
Kainedogg Registered User Join Date: May 2012 Location: MacDill AFB\Tampa Posts: 151	Re: LS3 heads versus LS6 heads? I was thinking of doing the LS3 heads my self but for the added cost and the hp increase in the higher rpm range, it just didn't make sense for my truck. If under the other hand if I was building a 408" stroker then the best bang for the buck heads would be the LS3's all day, especially with the valves now unshrouded. On a different note I have driven a buddy's truck with the LY6, cam and tune and it felt as quick, but not staggeringly quicker than a mutual friends older LQ4 with shaved iron heads and very small cam.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.