Hitch receiver for 66 c10

[lt1tyrell]

Hey looking to put a good heavy duty hitch receiver on my truck, anybody know if they will fit off of other year chevy trucks? Was hoping to grab one from a wrecker if possible. They seem a little harder to find for the 60-66 trucks, thanks.
Posted via Mobile Device

[Sharps40]

Post #374, page 15 of this thread

http://67-72chevytrucks.com/vboard/s...se#post6238320

Reese Number 37042

Wallmart on the shelf about $125

Advance auto, internet order, use code P20 and get 20% off and free shipping bringing yer cost to about $100.

The link details the install on John Lee, my 1965 C10 SBSS. Luck.

[NEWFISHER]

Sharps40-nice write up.

Anyone flip a hitch and run the stinger on a fold down license plate bracket so the stinger is above the bumper but below the bed for the hidden look?

[kieth]

Originally Posted by NEWFISHER

Sharps40-nice write up.

Anyone flip a hitch and run the stinger on a fold down license plate bracket so the stinger is above the bumper but below the bed for the hidden look?

I THINK YOU CAN FIND A HIDDEN HITCH HERE :

http://www.airbagit.com/Towing-Hitches-s/1665.htm


THEY EVEN HAVE THE FOLD DOWN LISC PLATE BRACKET. KIETH

MORE DETAIL: http://www.airbagit.com/Hidden-Trail...hit-gm6072.htm

[Rich 5150 69]

Hidden hitch..

[NEWFISHER]

Originally Posted by Rich 5150 69

Hidden hitch..

Rich, close to what i'm after without having more invested in re-chroming the bumper after modifying it than I would have in the hitch. I think I will just fab one up. I'm wanting it to come out at frame height and above the drop in the bumper so no square hole like yours.

[NEWFISHER]

Originally Posted by kieth

I THINK YOU CAN FIND A HIDDEN HITCH HERE :

http://www.airbagit.com/Towing-Hitches-s/1665.htm


THEY EVEN HAVE THE FOLD DOWN LISC PLATE BRACKET. KIETH

MORE DETAIL: http://www.airbagit.com/Hidden-Trail...hit-gm6072.htm

Thanks Keith, but when I call to order they say it's designed for their roll pan and can't guarantee it will work with a rear bumper. They don't have a tech dept. or any pic's or measurements of it mounted. I'll call back tomorrow morning and see if I can get a shift change salesperson as the one today brought the suck.

[Clyde65]

I used what Keith posted, I have a Roll Pan no bumper

[KJSR]

Looking at the one Sharps40 posted (thanks for the post and discount code, ordered mine today) it should be pretty easy to modify to tuck up just where you want it. For 100$ you can"t go wrong.....

[Sharps40]

Originally Posted by KJSR

Looking at the one Sharps40 posted (thanks for the post and discount code, ordered mine today) it should be pretty easy to modify to tuck up just where you want it. For 100$ you can"t go wrong.....

Glad to help. That promo code is pretty consistent for the last two or three years. It ain't often advertised but I memorized it cause its only three digits and its occasionally tied to an additional $50 email internet coupon on the next purchase.

Stick that hitch up in there and try it upside down, maybe that'll put it somewhere near the center of the bumper....I don't know if you can get it up as high as between the bed and the bumper but, since its a multipiece hitch, maybe ya can finagle it for a behind the license plate kind of set up.

I like mine where it is....thinking i'm gonna add a third brake light to it, since it might as well have a job to do when its not towin stuff or got a hitch haul hangin out of it.

[MisterC]

You might try giving the folks at Early Classic Enterprises a call. 888-777-0395

Their hidden hitch is designed for the 67-72 C/10's, but having mounted a 67-72 bumper on my '66, I can't help but think that this would fit close to where you want it.

[Blue666]

http://67-72chevytrucks.com/vboard/s...91#post6198791

Hope this helps