Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
01-14-2015, 01:41 AM | #1 |
is a fungineer
Join Date: Jan 2009
Location: Bakersfield, CA
Posts: 795
|
Long bed bedside and hood patch panel cuts
I have left and right '71 longbed bedsides and a GMC hood that I am going to cut up for patch panels. The bedsides were hit with a forklift when the truck that it was on was being moved. The hood has a couple dents.
These are all California solid metal, surface rust at worst. I am going to ask $10 per square foot of patch panel, plus shipping to you. I will post photos tomorrow. If you want to mark them up in a photo editing software or Paint for the areas that you would need, that might be the best way.
__________________
2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant |
01-14-2015, 01:10 PM | #2 |
Registered User
Join Date: Apr 2011
Location: Ft Liquordale, FL
Posts: 138
|
Re: Long bed bedside and hood patch panel cuts
Hi, I am interested in the sections indicated by the read square in this photo...need to fill those holes...
|
01-17-2015, 08:00 PM | #3 |
is a fungineer
Join Date: Jan 2009
Location: Bakersfield, CA
Posts: 795
|
Re: Long bed bedside and hood patch panel cuts
Driver's side:
Has a bow in front section trim bolt hole (pulled out) and squish marks on the bottom Tail light area also has a gouge Inside:
__________________
2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant |
01-17-2015, 08:05 PM | #4 |
is a fungineer
Join Date: Jan 2009
Location: Bakersfield, CA
Posts: 795
|
Re: Long bed bedside and hood patch panel cuts
Passenger side:
Squished part from forklift Inside
__________________
2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant |
01-17-2015, 08:07 PM | #5 |
is a fungineer
Join Date: Jan 2009
Location: Bakersfield, CA
Posts: 795
|
Re: Long bed bedside and hood patch panel cuts
Hood:
Dented corner on passenger side
__________________
2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant |
01-18-2015, 09:52 AM | #6 |
Registered User
Join Date: Jan 2013
Location: Bristol,In.
Posts: 1,118
|
Re: Long bed bedside and hood patch panel cuts
Would you be in to selling rear floor cuts? Need bout 8" of rear edge, thanks
|
01-18-2015, 06:02 PM | #7 |
is a fungineer
Join Date: Jan 2009
Location: Bakersfield, CA
Posts: 795
|
Re: Long bed bedside and hood patch panel cuts
Floor and header panel are not for sale, getting put into my truck, sorry.
Will have a wood floor header panel for sale in the future.
__________________
2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant |
01-20-2015, 03:07 AM | #8 |
Registered User
Join Date: Aug 2013
Location: Rochester Wa.
Posts: 395
|
Re: Long bed bedside and hood patch panel cuts
Hi, Did you still have the passenger bed side available>? Id be interested in the wheel well section out of it if your going to make patch panels from it, Possibly the whole thing now that I look at the pic of mine.....
Thanks Andy
__________________
64 C10 Fleetside LB 4 Sp/292 Build http://67-72chevytrucks.com/vboard/s...d.php?t=602438 70 GMC 1500 Fleetside LB 3OT/350 Build http://67-72chevytrucks.com/vboard/s...83#post6767983 76 GMC CCLB Dually Build http://67-72chevytrucks.com/vboard/s...d.php?t=691612 79 GMC 3500 Fleetside LB 454/400 90 Suburban Silverado 4x4 350/700R4 97 1500 Cheyenne Short Fleet 350/5sp |
01-21-2015, 04:04 PM | #9 |
is a fungineer
Join Date: Jan 2009
Location: Bakersfield, CA
Posts: 795
|
Re: Long bed bedside and hood patch panel cuts
Sure do, have the entire thing still... how much of the wheel well do you need?
These are getting cut up for scrap this weekend minus whatever anyone needs, they have to go.
__________________
2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant |
01-24-2015, 02:39 AM | #10 |
Hittin E-Z Street on Mud Tires
Join Date: Nov 2004
Location: Greenville, SC
Posts: 23,090
|
Re: Long bed bedside and hood patch panel cuts
I have a couple of requests...
I definitely need a 6" piece from the lower rear of the DS quarter. Cutting it at the bodyline would be fine, then 8" back from the wheel well should be a safe amount. It looks straight in the pic... is that line just from the trim piece or is there a crease there? Also, I fubared the back section of my bed (again still driver side), it would be difficult to straighten, but if I could weld in a new section that would be great. I don't need the taillight area, so you could cut it right at the very back of the bed, before it curves around, then right above where the top bodyline starts to roll over, then at the bottom bodyline, to near the wheel well. That is, if it's straight (looks like it is.) Those cuts should leave a somewhat flat panel. I'd also like a small 1' square piece about an inch above the bodyline on a clean piece somewhere in the middle front section (going to use that for turn signal filler patches, etc) Again, shipping could be a deal breaker on the bigger piece I want, but I definitely want the smaller quarter wheel well patch if that area is straight and the 1' square piece. Do you have any way to estimate shipping to Taylors, SC? Also, if it saves money, I can give you my work address for shipping.
__________________
Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! Last edited by 67ChevyRedneck; 01-24-2015 at 03:06 AM. |
01-24-2015, 03:00 AM | #11 |
Hittin E-Z Street on Mud Tires
Join Date: Nov 2004
Location: Greenville, SC
Posts: 23,090
|
Re: Long bed bedside and hood patch panel cuts
I'm trying to save a pretty nice straight set of 68 bed sides, I already welded in some wheel well patches from New Mexico... if I can fix THOSE areas I can fix the rest!
__________________
Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! |
01-27-2015, 01:59 PM | #12 |
Hittin E-Z Street on Mud Tires
Join Date: Nov 2004
Location: Greenville, SC
Posts: 23,090
|
Re: Long bed bedside and hood patch panel cuts
Bump?
__________________
Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! |
01-27-2015, 02:52 PM | #13 |
Senior Member
Join Date: Sep 2007
Location: Albuquerque NM
Posts: 7,862
|
Re: Long bed bedside and hood patch panel cuts
any cab sections avail?
__________________
1967custom |
01-29-2015, 04:54 PM | #14 |
Hittin E-Z Street on Mud Tires
Join Date: Nov 2004
Location: Greenville, SC
Posts: 23,090
|
Re: Long bed bedside and hood patch panel cuts
Bump... hoping the OP is checking the forum as a guest? (hasn't logged in since 1-23)
__________________
Jesse James 1967 C10 SWB Stepside: 350/700R4/3.73 1965 Ford Mustang: 289/T5-5spd/3.25 Trac-Loc 1968 Pontiac Firebird: Project Fire Chicken! 2015 Silverado Double Cab 5.3L Z71 2001 Jeep Wrangler Sport 4.0L 5spd 2020 Chevrolet Equinox Premium 2.0L Turbo 2011 Mustang V6 ~ Wife's ride American Born, Country by the Grace of God 1967 CST Shop Truck Rebuild! My 1967 C-10 Build Thread My Vintage Air A/C Install Project "On a Dime" Trying my hand at Home Renovation! 1965 Mustang Modifications! |
03-27-2015, 04:16 PM | #15 |
is a fungineer
Join Date: Jan 2009
Location: Bakersfield, CA
Posts: 795
|
Re: Long bed bedside and hood patch panel cuts
Sorry guys, due to some personal circumstances I had to scrap everything.
Nothing left.
__________________
2003 S10, 2.2 auto- the daily driver, currently with a 2"/2" drop and some minor engine bolt-ons 1978 Impala 2-door, race 350/T350 - the new race car, in progress 1968 Chevy C10 longbed- 3/5 drop, currently undergoing a heart transplant |
Bookmarks |
Tags |
bedside, hood, long bed, patch panels |
|
|