|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
02-26-2015, 07:40 PM
|
#1 |
|
Registered User
Join Date: May 2009
Location: Lebanon, Mo
Posts: 20
|
Gettin Parts Togather For My 6.0 Swap. Have Questions
Finally got my 2002 LQ4 w/317 heads and have a few questions about parts before I start buying.
1. I'm looking for a LS1/LS6 style intake. If I buy a LS1 or LS Qualifier Intake do I just buy a fuel rail off ebay and use my injectors from my truck intake? Also I'm switching over to DBC so do I just buy the throttle body to switch it over? 2. My motor came without a harness. Can I use a harness from any 4.8/5.3 or 6.0 since I'm sending it off for stand alone anyway? 3. Same question for the ECM. Since Im sending it off does it have to be a 6.0 or will any LS ECM work? 4. What about the knock sensors, can I just swap to a flat valley pan without provisions to get rid of them? I'm sure Ill have tons more questions as I go along and try to do my research, but I'm chomping at the bits to order parts and just don't want to make a mistake.. Last edited by HuntinNut; 02-26-2015 at 07:51 PM. |
|
|
|
02-27-2015, 09:24 AM
|
#2 |
|
Registered User
Join Date: Dec 2002
Location: Cactus Patch So. Az
Posts: 4,749
|
Re: Gettin Parts Togather For My 6.0 Swap. Have Questions
Watching this one !
__________________
53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD) 53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25 55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73 62 Solidaxle Corvette Roman Red (327 340hp 4spd 3:36) C4 & C5 suspension tube chassis LS 3 4L70E 65 Corvette Coupe 327 350hp 4spd 4:11 78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42 2000 S-Type 3.0 (wife cruiser) 2003 GMC SCSB 5.3 4L60E 3:42 |
|
|
|
|
02-27-2015, 10:41 AM
|
#3 |
|
It's alsways something.....
 
Join Date: Nov 2008
Location: Douglasville GA
Posts: 1,171
|
Re: Gettin Parts Togather For My 6.0 Swap. Have Questions
Quote:
2. My motor came without a harness. Can I use a harness from any 4.8/5.3 or 6.0 since I'm sending it off for stand alone anyway? 3. Same question for the ECM. Since Im sending it off does it have to be a 6.0 or will any LS ECM work? My Opinion: Best strategy here is to ask whoever you plan to do the harness mod and PCM tuning.
__________________
1968 RS Camaro 'Vert Matching number 327 and M21 Muncie 1968 C10 Black with red interior and orig paint. 5.3 / 4l60e,3:73 POSI 17" Torq Thrusts 1968 CST 514 Red with black interior. Buddy Buckets, Factory A/C, PS, PB- 20" AR custom shop TT, 5.3 and 4l60e |
|
|
|
|
02-27-2015, 11:10 PM
|
#4 |
|
Registered User
Join Date: Jan 2012
Location: Petal,Ms.
Posts: 428
|
Re: Gettin Parts Togather For My 6.0 Swap. Have Questions
The injectors will not work get some for the ls1/6 intake. The harness can be made to work but its gona cost more since it was dbc, and you want dbw, so all those wires and connector will have to be added. And injector connectors will need to be changed if harness came from truck. Also you need tac and petal assembly.
Get a harness from the setup you want to run, saves lots of money. Or order a standalone that you need. |
|
|
|
|
02-28-2015, 12:31 AM
|
#5 | |
|
Registered User
Join Date: May 2009
Location: Lebanon, Mo
Posts: 20
|
Re: Gettin Parts Togather For My 6.0 Swap. Have Questions
Quote:
|
|
|
|
|
|
02-27-2015, 11:26 PM
|
#6 |
|
Registered User
Join Date: Sep 2014
Location: Milwaukie, OR
Posts: 223
|
Re: Gettin Parts Togather For My 6.0 Swap. Have Questions
I bought a stand alone harness from BP Automotive, it was less than buying a GM harness and having it redone and its a much nicer setup that a redone one. If you call BP Automotive they can help you out a lot and answer questions, plus they are a sponsor on this site.
Rich |
|
|
|
|
03-01-2015, 08:14 PM
|
#7 |
|
Registered User
Join Date: Jan 2012
Location: Petal,Ms.
Posts: 428
|
Re: Gettin Parts Togather For My 6.0 Swap. Have Questions
Sorry misread the post, either harness should work then. Delete what you dont need,
|
|
|
|
|
| Bookmarks |
|
|
Hybrid Mode
