![]() |
|
![]() |
#1 |
Registered User
Join Date: Jun 2014
Location: reno nv
Posts: 10
|
Gasket remover
I'm trying to remove the old paper gaskets under the access covers on the side of the 4spd xmission on my C20. I had some old NAPA spray gasket remover that worked pretty well, but they don't sell it anymore. I tried Permatex remover. It is better than nothing, but not much. Any recommendations?
|
![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Feb 2014
Location: Los Angeles area :(
Posts: 499
|
Re: Gasket remover
razor blade? Scrape scrape scrape
__________________
'68 C10 SWB '85 K30 Blazer |
![]() |
![]() |
![]() |
#3 |
Registered User
Join Date: Mar 2009
Location: WARRENSBURG,MISSOURI,64093
Posts: 1,518
|
![]()
I've used those "Scotchbrite Roloc Disks" with an angle die grinder, just use the medium or fine grit stuff, I think its gray or blue in color.you don't want to dwell in the same area too long, it will remove metal if you do.
Just a recommendation. Ben ![]() |
![]() |
![]() |
![]() |
#4 |
Registered User
Join Date: Jun 2008
Location: Moss Point,Ms.
Posts: 1,439
|
Re: Gasket remover
Wire wheel on a 4" grinder does it for me!
Mike. ![]() |
![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jul 2015
Location: Central Coast, CA
Posts: 501
|
Re: Gasket remover
I've had good results using a heat gun to soften the gasket and its adhesive and permit easier scraping but not in a confined space where plastic or rubber parts are nearby or especially where there are automotive oils or fuel of course..
|
![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Nov 2014
Location: Austin
Posts: 749
|
Re: Gasket remover
...until a piece of wire from the wheel ends up it the case/engine/whatever...scary. I am in the razor blade crowd. But, on most of the car shows, you see them using die/angle grinders with what is probably scotch-brite pads. For me, that is uncontrolled debris flying everywhere.
|
![]() |
![]() |
![]() |
#7 |
Registered User
Join Date: Nov 2014
Location: Austin, TX
Posts: 281
|
Re: Gasket remover
![]()
__________________
72 K2500 Sierra Longbed Wideside 350/TH350/NP205 66 Plymouth Barracuda 225 Slant6 |
![]() |
![]() |
![]() |
#8 |
Registered User
Join Date: Nov 2014
Location: Austin
Posts: 749
|
Re: Gasket remover
I have a "gasket scraper" tool in my tool box (see above), but generally it only gets used to scrap grease from parts I am cleaning up. Not sharp enough for most gasket removal tasks.
Last edited by Davidf; 03-02-2016 at 03:23 PM. Reason: removed photo, redundant |
![]() |
![]() |
![]() |
#9 |
Registered User
Join Date: Jul 2010
Location: MD
Posts: 1,937
|
Re: Gasket remover
__________________
1969 c-10 Step Side Long Bed. I-6 250cid = ![]() |
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Jan 2011
Location: Delaware and Long Island, New York
Posts: 3,464
|
Re: Gasket remover
Razer blades always worked for me
|
![]() |
![]() |
![]() |
#11 |
Registered User
Join Date: Jun 2014
Location: reno nv
Posts: 10
|
Re: Gasket remover
Thanks for all the thoughtful responses. I ended up using a single edge razor blade. There was enough room to get to it.
|
![]() |
![]() |
![]() |
#12 |
Special Order
![]() ![]() Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
|
Re: Gasket remover
Elbow grease never let me down
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
![]() |
![]() |
![]() |
Bookmarks |
|
|