Is this piece of clutch linkage available?

[TJ's Chevy]

Hey guys, I am either going to have to repair this or purchase a new one if they are available....so that leads to my question...what's the best way to repair this? I know...fill weld it and grind smooth....which I am terrible at. haha Are new ones produced? As you can see from the wear...I doubt it will last a very long time under the load of a new pressure plate.

[1963c-10]

pretty sure I have one sitting on the extra parts shelf TJ. Ill check at 6pm my time and let you know tomorrow. Just cover the postage and its yours. I have a complete assembly from a friend who converted from manual to auto.

[TJ's Chevy]

Originally Posted by 1963c-10

pretty sure I have one sitting on the extra parts shelf TJ. Ill check at 6pm my time and let you know tomorrow. Just cover the postage and its yours. I have a complete assembly from a friend who converted from manual to auto.

Thanks man! If it's in good shape SOLD! lol!

[Blue666(2)]

Can you get a more clear picture?

I was looking here but could not find it. Lots of other good stuff.

http://www.amkproducts.com/default.htm

[Blue666(2)]

Check on page 313 & 314. See if those descriptions are what you need.

http://www.amkproducts.com/Catalog_PDF/308-402.pdf

[Haaland]

I also have one, I won't be needing anymore when I do my swap. Same deal postage and it's yours.

[TJ's Chevy]

Originally Posted by Haaland

I also have one, I won't be needing anymore when I do my swap. Same deal postage and it's yours.

Thanks man! PM sent.

[TJ's Chevy]

Originally Posted by Blue666(2)

Can you get a more clear picture?

I was looking here but could not find it. Lots of other good stuff.

http://www.amkproducts.com/default.htm

Originally Posted by Blue666(2)

Check on page 313 & 314. See if those descriptions are what you need.

http://www.amkproducts.com/Catalog_PDF/308-402.pdf

Thanks for the links! Took a look, but they only have the rods and bushings. Not this piece that I could find...course I don't even know what it is supposed to be called. lol Will have to look in the manual.

[1963c-10]

Here's the pics tj. Can have the whole rod assembly or I'll ship just the fitting.....Up to you

[TJ's Chevy]

Originally Posted by 1963c-10

Here's the pics tj. Can have the whole rod assembly or I'll ship just the fitting.....Up to you

Just the fitting would be awesome. Let me know on shipping. Thanks!

[padresag]

You can buy them new
ron

[padresag]

over 8,000 posts on here and you would think he would look here
http://www.lmctruck.com/icatalog/cbe/full.aspx?Page=89
ron

[jtrichard]

No o fence but that one don't look any better than the one you have i would braze yours up or get a new one

[1963c-10]

Originally Posted by jtrichard

No o fence but that one don't look any better than the one you have i would braze yours up or get a new one

The pic does it no justice. Other than grease and dirt it's a solid piece. Pic taken in the barn while dark. It's also a free part that I'd comfortably run with no problem.

[TJ's Chevy]

Never ordered from LMC so I never checked.

63C10: I noticed it looked worn out, but since I don't have any spares I figured a couple to keep in the glove box just in case is better than none at all! haha But you mentioned it's solid so that's awesome.

[TJ's Chevy]

After checking Orange County truck and car shop, Classic Parts of America, Napa, and O'reilly auto I didn't think to check LMC so I checked here. Thanks to all those for Helping rather than make a big deal about it.

[padresag]

truck and car shop https://issuu.com/truckandcarshop/docs/ts_60-72_web
bottom page 127
ron

[1963c-10]

Pm me your address TJ and I'll mail it to you. You won't have any issues with it. Any other clutch linkage parts you need?

[61K10]

Is the notch suppose to be in the round shaft?

[TJ's Chevy]

Originally Posted by 61K10

Is the notch suppose to be in the round shaft?

According to the pictures of new ones I don't think so. Due to the fact those parts are never lubed the notch would appear after many years of use....Heck they lasted 50 years! lol I am sure it would last many more to, but rather have new. haha

[padresag]

Originally Posted by 61K10

Is the notch suppose to be in the round shaft?

that is wear
ron

[thunder71]

I'm a welder and see a easy repair on that part...weld it and file it back to shape.

[1963c-10]

The notch looked machined flat....if its from wear, I would replace with a new part for $13. I will try and get home before dark and get better pics and relook at it.

[1963c-10]

I looked at the part again last night TJ and I have to agree with the forum. Downside of a dark barn.....the part does have a groove worn into it. With that being said, I have no problem shipping it if you still want it. It has been mentioned that it is an easy fix, but the option is your to decide. Just let me know.

Jon

[TJ's Chevy]

Originally Posted by 1963c-10

I looked at the part again last night TJ and I have to agree with the forum. Downside of a dark barn.....the part does have a groove worn into it. With that being said, I have no problem shipping it if you still want it. It has been mentioned that it is an easy fix, but the option is your to decide. Just let me know.

Jon

Sure, I'll still take it. Like said, a few spares worn out or not can't hurt. Better than nothing! Since they are reproduced I will order a new one next time I place a parts order which will be soon. Thanks Jon!