PB Stage 2 Deluxe Front Kit

[SierraMtns]

I am back working on the truck...

Could PB Stage 2 Deluxe Front Kit be used with springs?

My plan is to buy a used front cross member and then run PB Stage 2 Deluxe Front Kit since those A-arms are redesigned and run 1" forward.

I would still need springs, drop spindles, rack-n-pinion, brakes and rotor (5 lug).

You guys think this is possible to do all this for $2,500?

Thanks

Also is PBfab now c10shop?

[bbbc10]

Have you lookef at their website? Contact them? Think they sell an adapter to run springs but it would be best to msg them....an never heard of c10shop doubt they would change names

[68is4me]

Originally Posted by bbbc10

Have you lookef at their website? Contact them? Think they sell an adapter to run springs but it would be best to msg them....an never heard of c10shop doubt they would change names

I get emails from them and the emails come as c10shop. The emails are usually info about what is new in the shop.

[Willie Makeit]

porterbuilt fabrication is still known as http://pbfab.com

[68is4me]

You can buy adapters form PB for the coil spring. If you are running a stock crossmember you do not need to add a rack and pinion steer. Stock will do just fine. $2,500 is going to be tuff I think just the PB stuff will cost $1,800. I hope you are in no hurry or hopefully have the stuff ordered from PB. Took me 2 months to get control arms for mine just this spring.

[Ram-Man]

http://c10shop.com same physical address as porterbuilt. Looks like they are running two websites. Either way the quality of the porterbuilt products are hard to beat. They are worth the wait..

[bbbc10]

Have seen ppl have problems with them lately though

[Willie Makeit]

Originally Posted by bbbc10

Have seen ppl have problems with them lately though

Yes they have. Loooooooooong lead times. Parts made wrong. Will not answer phone or reply to customer's emails or phone calls when leaving a message.

Nothing like the reviews I had read in the past.

[andrewmp6]

Unless you want air bags later on http://www.nolimitengineering.com/pr...tegory=6157532 Or http://www.scottshotrods.com/1963-87...k-bolt-in-ifs/

[68Stepbed]

Another option. https://totalcostinvolved.com/produc...o-touring-ifs/

[SierraMtns]

Update:

I ordered this kit with springs. I had fast response times on emails, under 24 hours. Brandon help me out with all my questions. I order the kit with 1"narrowed and 1" forward arms.

Now the fun part....waiting. Current build time is 6 weeks.

[Willie Makeit]

Originally Posted by SierraMtns

Now the fun part....waiting. Current build time is 6 weeks.

I was told 3-4 weeks delivery when i placed the order. Finally got them somewhere around 8 weeks.

FYI - Be sure to check the grease fitting holes very very closely. Uppers were good but my lowers were drilled oversize and had flat threads - zerks would not tighten. I had to drill next larger size, re-tap and purchase new zerks.

[drfloyd]

I bought No Limit's Wide Ride. Along with the rear 4 link. Almost no lead time on their stuff. Quality is as good as any.

[SierraMtns]

Originally Posted by drfloyd

I bought No Limit's Wide Ride. Along with the rear 4 link. Almost no lead time on their stuff. Quality is as good as any.

Yeah I have NL trailing arm kit. But couldn't do their front. Price just kept going up so I went with PB so I can put more money on the motor/trans.

[SierraMtns]

Originally Posted by drfloyd

I bought No Limit's Wide Ride. Along with the rear 4 link. Almost no lead time on their stuff. Quality is as good as any.

Originally Posted by Willie Makeit

I was told 3-4 weeks delivery when i placed the order. Finally got them somewhere around 8 weeks.

FYI - Be sure to check the grease fitting holes very very closely. Uppers were good but my lowers were drilled oversize and had flat threads - zerks would not tighten. I had to drill next larger size, re-tap and purchase new zerks.

How long ago was this? Did you try and return the parts to them?

Thank you for sharing this with us. Good to know what to watch out for.

I don't want this thread to turn into a PB bashing thread but it would be nice to know how they handled it?

[Willie Makeit]

Originally Posted by SierraMtns

How long ago was this? Did you try and return the parts to them?

Thank you for sharing this with us. Good to know what to watch out for.

I don't want this thread to turn into a PB bashing thread but it would be nice to know how they handled it?

This was within the past 2-3 weeks. I didn't get return calls for the previous messages left and I didn't have another 8 weeks to wait on another set of lower arms so I repaired them myself.

I don't see it as bashing, only sharing my experience.

[SierraMtns]

Originally Posted by Willie Makeit

This was within the past 2-3 weeks. I didn't get return calls for the previous messages left and I didn't have another 8 weeks to wait on another set of lower arms so I repaired them myself.

I don't see it as bashing, only sharing my experience.

Yeah I dont feel its bashing either.


So did they make it right for you? Give you a discount on your next order? Money back? Would you order from them again?

Do you have any pictures of the front end put together?

Thanks

[PBFAB.COM]

Originally Posted by SierraMtns

Update:

I ordered this kit with springs. I had fast response times on emails, under 24 hours. Brandon help me out with all my questions. I order the kit with 1"narrowed and 1" forward arms.

Now the fun part....waiting. Current build time is 6 weeks.

Did you get your kit yet? If you email me your order #, I'll give you an update on build time.

Brandon

[SierraMtns]

Originally Posted by PBFAB.COM

Did you get your kit yet? If you email me your order #, I'll give you an update on build time.

Brandon

Not yet. I placed my order on 6/15. So I am still in the back of the line...ha ha

[PBFAB.COM]

Hey Willie,

Next time reach out to us. We would've been happy to fix the issue with your control arms. This is the first time we've heard of any issue with the zerk holes being too big or oversized. It would be extremely rare for it to happen on just one set since they are produced in batches. We also would have made your replacement arms, if necessary, in a day or two. On another note, we keep every single email and voicemail. I can promise you that we have never not returned a call or email intentionally. So please accept my apology if that occurred.

It's no secret our build times are longer than most. You guys all know the story. We build everything in house. We pride ourselves on the quality of our parts. It's what we're known for. Do we make mistakes, of course. With the volume we do, it'd be impossible not to mess up once in a while. But we ALWAYS stand behind our product and our work. We will fix any issue.

If you guys have any questions, pleas shoot me an email. I'll be happy to talk. brandon@pbfab.com

Oh, and C10 Shop is across the street. They sell PB stuff along with some other components. Not owned by PB.

Brandon

[Willie Makeit]

Brandon

I called and spoke to you directly. I asked for torque specs for the cross shaft nuts. You stated to me that Nathan was busy welding and you needed to speak to him and would call me back in 5 minutes with that information. I never rec'd that call. I eventually found a thread on this board where Nathan said that the nut should bottom out the crush sleeve bushing then go an additional 1/4 turn. That's what I did.

As far as the zerks, it wasn't the zerk fitting being undersize, the hole itself was oversize. As a machinist for over 25 years, it was fairly easy for me to spot the issue. Guys not familiar with metal working and proper tap drills may not realize the issue.

Not meant as a bash by any means. Some of the nicest components I've ever purchased and just wanted to point out my experience. A set of instructions on the control arm kit would go a long way to help explain some of the small things that pop up. Hope my input helps you guys improve your processes and products.

[PBFAB.COM]

Originally Posted by Willie Makeit

Brandon

I called and spoke to you directly. I asked for torque specs for the cross shaft nuts. You stated to me that Nathan was busy welding and you needed to speak to him and would call me back in 5 minutes with that information. I never rec'd that call. I eventually found a thread on this board where Nathan said that the nut should bottom out the crush sleeve bushing then go an additional 1/4 turn. That's what I did.

As far as the zerks, it wasn't the zerk fitting being undersize, the hole itself was oversize. As a machinist for over 25 years, it was fairly easy for me to spot the issue. Guys not familiar with metal working and proper tap drills may not realize the issue.

Not meant as a bash by any means. Some of the nicest components I've ever purchased and just wanted to point out my experience. A set of instructions on the control arm kit would go a long way to help explain some of the small things that pop up. Hope my input helps you guys improve your processes and products.

Willie,

I apologize Nate never called you back with the torque specs. We're typically very efficient at returning calls.

As for the zerk fittings, if it was an issue why didn't you mention it on the phone? I'd have been happy to resolve the issue. Even more important is being made aware of it. That part comes directly from our machine shop, so I'll reach out to them tomorrow to be sure they are aware. We certainly don't want a batch of lower arms going out with a zerk fitting issue.

Please let us/me know next time you have a problem. If we aren't informed, we don't have an opportunity to fix it. I try hard to provide excellent customer service. Sometimes I fail, and I apologize that happened in this case.

Brandon

[Willie Makeit]

Originally Posted by PBFAB.COM

Willie,

I apologize Nate never called you back with the torque specs. We're typically very efficient at returning calls.

As for the zerk fittings, if it was an issue why didn't you mention it on the phone? I'd have been happy to resolve the issue. Even more important is being made aware of it. That part comes directly from our machine shop, so I'll reach out to them tomorrow to be sure they are aware. We certainly don't want a batch of lower arms going out with a zerk fitting issue.

Please let us/me know next time you have a problem. If we aren't informed, we don't have an opportunity to fix it. I try hard to provide excellent customer service. Sometimes I fail, and I apologize that happened in this case.

Brandon

That's because I had not yet discovered that issue. After the multiple delays in shipping combined with not getting response to my questions, I didn't have a lot of confidence that i would get a reply to the Zerk issue.

no offense, but i honestly didn't have time to wait on you guys to "make it right." I had already waited approx 8 weeks on my arms after being told that it would be 3-4 weeks when i originally placed the order.

If i may, let me be blunt for a moment - i get it you guys have long lead-times, that was understood when I originally considered your products - but when one places an order & their confidence in a vendor based on the delivery information that was supplied by said vendor (aka: his word) at the time of order to discover afterwards that this information is false/not accurate, then it doesn't exactly leave one with a "warm and fuzzy" if you know what i mean.

[PBFAB.COM]

Originally Posted by Willie Makeit

That's because I had not yet discovered that issue. After the multiple delays in shipping combined with not getting response to my questions, I didn't have a lot of confidence that i would get a reply to the Zerk issue.

no offense, but i honestly didn't have time to wait on you guys to "make it right." I had already waited approx 8 weeks on my arms after being told that it would be 3-4 weeks when i originally placed the order.

If i may, let me be blunt for a moment - i get it you guys have long lead-times, that was understood when I originally considered your products - but when one places an order & their confidence in a vendor based on the delivery information that was supplied by said vendor (aka: his word) at the time of order to discover afterwards that this information is false/not accurate, then it doesn't exactly leave one with a "warm and fuzzy" if you know what i mean.

Willie,

Totally get it. Sorry you didn't have a great experience. I'll try to do better if we have an opportunity in the future.

Brandon

[Willie Makeit]

Originally Posted by PBFAB.COM

Willie,

Totally get it. Sorry you didn't have a great experience. I'll try to do better if we have an opportunity in the future.

Brandon

Fabricated parts are top notch! Just wish some of the other was a bit better.

You guys will definitely have another opportunity based on the responsiveness in this conversation thread and the quality of the parts.

Parts are installed and truck is back on the road. It's all good!