The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 09-16-2018, 12:38 AM   #1
MARTINSR
Registered User
 
MARTINSR's Avatar
 
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
Need some help with AD rad support.

My upper tie bar wasn't welded to the rad support. I had forgotten that it's suppose to be and had it sand blasted, now find that I need to weld it to the rad support, or maybe I will make it bolt on properly adding a tab where it was welded and put a bolt.

But what about the cross rod supports, where the heck does it mount, the bolts broken off but I see no where that it would have mounted.

Brian
Attached Images
  
__________________
1948 Chevy pickup
Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats!
Bought with paper route money in 1973 when I was 15.

"Fan of most anything that moves human beings"
MARTINSR is offline   Reply With Quote
Old 09-16-2018, 09:30 AM   #2
oldman3
Senior Member
 
oldman3's Avatar
 
Join Date: Mar 2011
Location: West Plains, Missouri
Posts: 7,559
Re: Need some help with AD rad support.

Martin, this isn't a very good pic, but all I have. I could be wrong, but the "X" brace is welded to the radiator support. Then there are two support rods that are bolted to the radiator support and go to the front grill support. You have to look real close but you can see the "X" brace. Hope this helps...Jim
Attached Images
 
oldman3 is offline   Reply With Quote
Old 09-16-2018, 10:24 AM   #3
oldman3
Senior Member
 
oldman3's Avatar
 
Join Date: Mar 2011
Location: West Plains, Missouri
Posts: 7,559
Re: Need some help with AD rad support.

Martin, looked in the manual and found this, it should clear up my previous post...Jim
Attached Images
 
oldman3 is offline   Reply With Quote
Old 09-16-2018, 10:36 AM   #4
MARTINSR
Registered User
 
MARTINSR's Avatar
 
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
Re: Need some help with AD rad support.

The rods are welded in? I have to take a run out there again to see, I was just out looking at it and didn't see that.

Brian
__________________
1948 Chevy pickup
Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats!
Bought with paper route money in 1973 when I was 15.

"Fan of most anything that moves human beings"
MARTINSR is offline   Reply With Quote
Old 09-16-2018, 10:48 AM   #5
MARTINSR
Registered User
 
MARTINSR's Avatar
 
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
Re: Need some help with AD rad support.

Damn, how simple is that! I didn't look at the other end of the rods thinking they were bolted on, LOLOLOL. Just checked, and sure enough, they weld on the inside of the support, geeez, thanks.

I did see another screwup though, the end of the upper horizontal support that goes out over the fender has ben cut off. So I will need to take this off my old rad support (that's all cut up on the bottom from my Camaro clip fiasco) and put it on this one.

Brian
Attached Images
 
__________________
1948 Chevy pickup
Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats!
Bought with paper route money in 1973 when I was 15.

"Fan of most anything that moves human beings"
MARTINSR is offline   Reply With Quote
Old 09-17-2018, 12:30 AM   #6
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,710
Re: Need some help with AD rad support.

Good catch, Makes you wonder why it was cut off though.
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is offline   Reply With Quote
Old 09-17-2018, 12:34 AM   #7
MARTINSR
Registered User
 
MARTINSR's Avatar
 
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
Re: Need some help with AD rad support.

The only thing I can think of is that the nut stun on the underside and they just cut it to take the front end apart?

Brian
__________________
1948 Chevy pickup
Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats!
Bought with paper route money in 1973 when I was 15.

"Fan of most anything that moves human beings"
MARTINSR is offline   Reply With Quote
Old 09-17-2018, 11:12 AM   #8
b-mac
Registered User
 
b-mac's Avatar
 
Join Date: Mar 2014
Location: Wichita
Posts: 519
Re: Need some help with AD rad support.

I don't have any of these rods...wonder how important they are.
b-mac is offline   Reply With Quote
Old 09-17-2018, 12:03 PM   #9
MARTINSR
Registered User
 
MARTINSR's Avatar
 
Join Date: Dec 2000
Location: Boise, Idaho
Posts: 6,003
Re: Need some help with AD rad support.

Quote:
Originally Posted by b-mac View Post
I don't have any of these rods...wonder how important they are.
The rad support I am replacing with this one didn't have them and it has been on my truck at least since 1974 when I bought it so I don't think there is a big reason for them.

Brian
__________________
1948 Chevy pickup
Chopped, Sectioned, 1953 Corvette 235 powered. Once was even 401 Buick mid engined with the carburetor right between the seats!
Bought with paper route money in 1973 when I was 15.

"Fan of most anything that moves human beings"
MARTINSR is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:29 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com