The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1973 - 1987 Chevrolet & GMC Squarebody Pickups Message Board > The 1973 - 1991 Blazers, Jimmys, and Suburbans Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-29-2018, 11:53 AM   #1
Grizz1963
Registered User
 
Grizz1963's Avatar
 
Join Date: Dec 2012
Location: Rochester, KENT
Posts: 10,575
79 Blazer 2WD Front end torque settings??

Hi all,

Managed to strip and replace most of the front end service items on my 79 Blazer over the weekend.

Does anyone have a simple chart of reference page to get all the torque settings for the front end.

Mine ended up looking like this and then back to normal with nothing torqued down.

So we continued to dismantle, clean, strip and swear from time to time. (I do most of the swearing, @PaulY jut get on with it)

The amount of dirt stuck to this truck, possibly the same as most or many other 40 year olds is staggering, possible a good rust preventative though.

Both sides torn down.




Next job of course was to clean, service and refit new parts to the Control arms.



The springs removed form the truck were as impressive as any that had been torched before.

Useful only as ballast when weighing something in.

Take a good look.

Before you burn them.

Measuring 11 inches.



So a new pair were selected from the pile, and measured, offered up and then Dr Bosch Grinder came in.

Surgery.

13 inches saved to be fitted.

Happy.



The next big job was a YouTube research job......

Easiest way to remove the 40 year old swing arm bushes.

Dr Bosch Drill to theatre.

Bench mounted, a few large drill bits sacrificed

Two per swing arm = 8 total.



Followed by Mr Press.

This tool, belonging to @PaulF was the most sensible thing to bring to the party.

Not always easy to use, needed loads of small custom pressing pieces made through the day, each taking time, and finding the right materials being a pain too, it worked a treat.



New brake shoes added while the front end was dismantled.



As we got busier and time drained away, I took less photos.

Needles to say, once the old bushes were removed and the new once’s pressed into place, often necessitating restarts the Ball joints were removed, replaced and then I took each piece out to a tree, hung them and painted the fresh metal in underbody sealer, getting a lovely uniform and clean look.

By 8.30 Paul had completed the reassembly, I still need to go back to torque up everything, change the position of the passenger side lover swing arm arm as it seems to have escaped the locating points.
Brake on passenger side needs bleeding.
Then I need to do the steering or tie rod ends, as we ran out of daylight and ambition, the cold is a killer.
Finally I also need to remove and replace the existing front wheel bearings.

Tired but happy, we closed shop at 8.30

Sleep was a problem for me, netting a total of three hours, and then awake for 4 hours, followed by another hour.

Today it was rain, wind and 5’C all day, so I decided to go shopping for food, paint and Silver Hammmerite for the wheels once the sun returns.

This afternoon I popped down to the garage to check the height and get a pic of the new height.

A sure sign of us being tired toward the end.



Front end came up 35 mm

Looking a load better, rear seems to have gone down a bit, 5-10mm



So there you go.

One step closer to an MOT submission.

Thanks for checking in and making your comments all.
__________________
MY BUILD LINK: http://67-72chevytrucks.com/vboard/s...585901]Redneck Express - 1966 C10 Short Fleetside
MY USA ROADTRIPS http://forum.retro-rides.org/thread/...2018-humdinger
IF YOU CAN'T FIX IT WITH A HAMMER, YOU'VE GOT AN ELECTRICAL PROBLEM MATE.
Grizz1963 is offline   Reply With Quote
Old 10-29-2018, 12:50 PM   #2
Grizz1963
Registered User
 
Grizz1963's Avatar
 
Join Date: Dec 2012
Location: Rochester, KENT
Posts: 10,575
Re: 79 Blazer 2WD Front end torque settings??

Found something.

http://www.73-87.com/7387garage/chas...n/frontend.htm
__________________
MY BUILD LINK: http://67-72chevytrucks.com/vboard/s...585901]Redneck Express - 1966 C10 Short Fleetside
MY USA ROADTRIPS http://forum.retro-rides.org/thread/...2018-humdinger
IF YOU CAN'T FIX IT WITH A HAMMER, YOU'VE GOT AN ELECTRICAL PROBLEM MATE.
Grizz1963 is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:36 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com