Wanted: automatic transmission linkage - The 1947 - Present Chevrolet & GMC Truck Message Board Network

NJKelly · 12-16-2018, 05:13 PM

I need the shift leaver and the bellcrank. The shift lever I have is not original, looks like it's out of a Chevelle from what I've seen on the internet. And bellcrank is original but the holes were attachs to the shift lever looks like they're enlarged due to wear. I was able to find a shift lever online a reproduction but would prefer original stuff. Anybody has any leads I'd appreciate it. Also need spring on pivot. Thanks.

**1968k20** · 12-16-2018, 05:28 PM

I might have part of it

NJKelly · 12-16-2018, 06:47 PM

Quote:

Originally Posted by 1968k20

I might have part of it

The middle piece with the bracket attached at the end with a cotter pin, that is the bellcrank I'm looking for. I can get a new shift leaver, brand new remanufactured. can you take a couple pictures of the holes where that shift lever goes into that bellcrank, it may be just as worn as mine. Thanks

**1968k20** · 12-16-2018, 11:25 PM

Quote:

Originally Posted by NJKelly

The middle piece with the bracket attached at the end with a cotter pin, that is the bellcrank I'm looking for. I can get a new shift leaver, brand new remanufactured. can you take a couple pictures of the holes where that shift lever goes into that bellcrank, it may be just as worn as mine. Thanks

I'll do that when I get home from work tomorrow

cori 64 · 12-17-2018, 11:51 AM

I have all of it!...Trade for right front bumper bracket!

**1968k20** · 12-17-2018, 11:37 PM

Pictures

**1968k20** · 12-17-2018, 11:44 PM

More

NJKelly · 12-18-2018, 12:00 AM

I need a picture of The notches, not the holes it's where the Shift lever fits in as in the picture above. Your first picture shows half what I'm talkin about

**1968k20** · 12-18-2018, 07:28 AM

Quote:

Originally Posted by NJKelly

I need a picture of The notches, not the holes it's where the Shift lever fits in as in the picture above. Your first picture shows half what I'm talkin about

here you go!

NJKelly · 12-18-2018, 11:07 AM

It's in a little bit better condition than mine but you can see that notch when you look at the picture on the left has a little wear. Mine is more exaggerated than that. I think I'm just going to weld then cut it out again. Thanks so much

**1968k20** · 12-18-2018, 02:46 PM

Quote:

Originally Posted by NJKelly

It's in a little bit better condition than mine but you can see that notch when you look at the picture on the left has a little wear. Mine is more exaggerated than that. I think I'm just going to weld then cut it out again. Thanks so much

No problem!

**richard2717** · 12-18-2018, 04:43 PM

I can take a look thru my box of them if you are still looking

NJKelly · 12-18-2018, 05:00 PM

I'm going to wait for the shift lever to come in and then just install it with the existing bellcrank. If that proves to be a problem I'm going to take the bellcrank off weld two notches shut and cut new notches. And if that fails I'll be reaching out to everybody again. Thanks for getting back to me.

12-16-2018, 05:13 PM	#1
NJKelly Registered User Join Date: Mar 2018 Location: New Jersey Posts: 379	Wanted: automatic transmission linkage I need the shift leaver and the bellcrank. The shift lever I have is not original, looks like it's out of a Chevelle from what I've seen on the internet. And bellcrank is original but the holes were attachs to the shift lever looks like they're enlarged due to wear. I was able to find a shift lever online a reproduction but would prefer original stuff. Anybody has any leads I'd appreciate it. Also need spring on pivot. Thanks. Attached Images

12-16-2018, 05:28 PM	#2
1968k20 Senior Member Join Date: Dec 2009 Location: Chester,California Posts: 5,632	Re: Wanted: automatic transmission linkage I might have part of it Attached Images __________________ 1977 Chevrolet K10 SWB Project 350/4spd/np205 1977 Chevrolet K20 LWB 350/350/203 1991 4Runner 22RE 5 SPD Yanmar Tractor 3 Cyl Diesel

12-17-2018, 11:51 AM	#5
cori 64 Registered User Join Date: Sep 2011 Location: yucaipa Posts: 50	Re: Wanted: automatic transmission linkage I have all of it!...Trade for right front bumper bracket!

12-17-2018, 11:37 PM	#6
1968k20 Senior Member Join Date: Dec 2009 Location: Chester,California Posts: 5,632	Re: Wanted: automatic transmission linkage Pictures Attached Images __________________ 1977 Chevrolet K10 SWB Project 350/4spd/np205 1977 Chevrolet K20 LWB 350/350/203 1991 4Runner 22RE 5 SPD Yanmar Tractor 3 Cyl Diesel

12-17-2018, 11:44 PM	#7
1968k20 Senior Member Join Date: Dec 2009 Location: Chester,California Posts: 5,632	Re: Wanted: automatic transmission linkage More Attached Images __________________ 1977 Chevrolet K10 SWB Project 350/4spd/np205 1977 Chevrolet K20 LWB 350/350/203 1991 4Runner 22RE 5 SPD Yanmar Tractor 3 Cyl Diesel

12-18-2018, 12:00 AM	#8
NJKelly Registered User Join Date: Mar 2018 Location: New Jersey Posts: 379	Re: Wanted: automatic transmission linkage I need a picture of The notches, not the holes it's where the Shift lever fits in as in the picture above. Your first picture shows half what I'm talkin about

12-18-2018, 11:07 AM	#10
NJKelly Registered User Join Date: Mar 2018 Location: New Jersey Posts: 379	Re: Wanted: automatic transmission linkage It's in a little bit better condition than mine but you can see that notch when you look at the picture on the left has a little wear. Mine is more exaggerated than that. I think I'm just going to weld then cut it out again. Thanks so much

12-18-2018, 04:43 PM	#12
richard2717 Equal opportunity joke ofender Join Date: Oct 2011 Location: Eastern Shore of MD Posts: 10,127	Re: Wanted: automatic transmission linkage I can take a look thru my box of them if you are still looking __________________ Members I have met. Dually Jams, OlBlue60, ScottH, Tommyboy24, Dujobo, Warbucket, 2003 Silverado, Notsolo, my90k5, 6t727t2, Special-K ,Jack_71C10, tabarcus,72blazer_mud_bogger,pwdcougar,RSavage,EricSean,1Rippen6,invicta455,tennaragtop71,arks, Kendal,Bennett68C10, Perpendicular, Chainsawman, McGeesCustomMinis,ShortbedClayton,longblue72,6768chevylover,Tim71,Travisarmenta,Ol' Drippy,fleetmitch,georgieb51,Dave,bcnya2,Dadsburb https://paypal.me/6772GMtruckparts Most women like the strong, silent type… Fortunately for me, my wife prefers the out-of-shape, mouthy type.

12-18-2018, 05:00 PM	#13
NJKelly Registered User Join Date: Mar 2018 Location: New Jersey Posts: 379	Re: Wanted: automatic transmission linkage I'm going to wait for the shift lever to come in and then just install it with the existing bellcrank. If that proves to be a problem I'm going to take the bellcrank off weld two notches shut and cut new notches. And if that fails I'll be reaching out to everybody again. Thanks for getting back to me.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.