Header selection.... - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ChadW · 02-07-2019, 11:32 AM

Need a set of headers for a sbc 327 with aluminium Trick Flow Twisted Wedge (angle plug) heads...going on a lowered/bagged 66 c10 so will probably need to be block huggers or a short header of some type that will keep the exhaust above the bottom of the frame rails. Thoughts, opinions etc?? Id like to find a midlength "clipster" header that will work.. something like these possibly?
https://www.ebay.com/itm/RACING-PERF...frcectupt=true

LVPhotos · 02-07-2019, 11:45 AM

If not manual, or use a hydraulic clutch bearing...
HOOKER 2466

ChadW · 02-07-2019, 11:50 AM

Quote:

Originally Posted by LVPhotos

If not manual, or use a hydraulic clutch bearing...
HOOKER 2466

Not manual...will be a 700r4..those are an option...would about any that are for a 67-81 camaro fit?

LVPhotos · 02-07-2019, 12:00 PM

This is another 62 with bars. I would check faq section... but sounds right. Or 67-72 truck

LVPhotos · 02-07-2019, 12:02 PM

My 62

**Captainfab** · 02-08-2019, 01:23 AM

Trying to find a combination of a shorty or mid length header that will also work with angle plug heads is going to be a challenge. I can say from experience that the Hedman 69260 headers that are made for these trucks will work with angle plug heads. But they do hang a little below the bottom of the frame. Since you are going with an auto trans (I assume you are removing the bellhousing crossmember) then you can use a set of 1st Gen Camaro or early Chevelle headers that are designed to work with angle plug heads. The car long tube headers do not drop down as far as truck headers. But any of those that will work, are going to be way more than the $100 ebay made in China headers.

**The Rocknrod** · 02-08-2019, 01:35 AM

Wouldn't 69230's work?

**Captainfab** · 02-08-2019, 01:48 AM

Yes, I forgot about those. I have read that they do work with angle plug heads despite what the installation notes say. And they don't hang down too low. Of course the bellhousing crossmember must be removed.

Quote:

Originally Posted by The Rocknrod

Wouldn't 69230's work?

ChadW · 02-08-2019, 12:12 PM

Thanks...I think i am leaning towards the Hooker 2466, midlength..I beleive they are ok with angle plugs as well..

02-07-2019, 11:32 AM	#1
ChadW Registered User Join Date: Jan 2018 Location: Danville, IL Posts: 160	Header selection.... Need a set of headers for a sbc 327 with aluminium Trick Flow Twisted Wedge (angle plug) heads...going on a lowered/bagged 66 c10 so will probably need to be block huggers or a short header of some type that will keep the exhaust above the bottom of the frame rails. Thoughts, opinions etc?? Id like to find a midlength "clipster" header that will work.. something like these possibly? https://www.ebay.com/itm/RACING-PERF...frcectupt=true

02-07-2019, 11:45 AM	#2
LVPhotos Registered User Join Date: Jan 2013 Location: Las Vegas, NV Posts: 1,857	Re: Header selection.... If not manual, or use a hydraulic clutch bearing... HOOKER 2466 Attached Images __________________ 1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081

02-07-2019, 12:00 PM	#4
LVPhotos Registered User Join Date: Jan 2013 Location: Las Vegas, NV Posts: 1,857	Re: Header selection.... This is another 62 with bars. I would check faq section... but sounds right. Or 67-72 truck Attached Images __________________ 1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081

02-07-2019, 12:02 PM	#5
LVPhotos Registered User Join Date: Jan 2013 Location: Las Vegas, NV Posts: 1,857	Re: Header selection.... My 62 Attached Images __________________ 1962 shortbed 408cui small block, TKO 600 5-speed, bagged Porterbuilt suspension. 18" Salt Flats http://www.cardomain.com/ride/332579...t-c-k-pick-up/ http://67-72chevytrucks.com/vboard/s...d.php?t=560081

02-08-2019, 01:23 AM	#6
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: Header selection.... Trying to find a combination of a shorty or mid length header that will also work with angle plug heads is going to be a challenge. I can say from experience that the Hedman 69260 headers that are made for these trucks will work with angle plug heads. But they do hang a little below the bottom of the frame. Since you are going with an auto trans (I assume you are removing the bellhousing crossmember) then you can use a set of 1st Gen Camaro or early Chevelle headers that are designed to work with angle plug heads. The car long tube headers do not drop down as far as truck headers. But any of those that will work, are going to be way more than the $100 ebay made in China headers. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

02-08-2019, 01:35 AM	#7
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: Header selection.... Wouldn't 69230's work? __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

02-08-2019, 12:12 PM	#9
ChadW Registered User Join Date: Jan 2018 Location: Danville, IL Posts: 160	Re: Header selection.... Thanks...I think i am leaning towards the Hooker 2466, midlength..I beleive they are ok with angle plugs as well..



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.