|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
03-05-2020, 11:54 AM
|
#1 |
|
Registered User
Join Date: May 2012
Location: Faith,NC
Posts: 1,626
|
Brake Booster Vacuum Hose Ideas
Help me solve this dilemma! So the nipple that the vacuum hose attaches to at the booster is too small for the correct size LS hose and I can't order the GM 15823207 nipple that works with the correct size hose because the hole in my booster is too big! My measurement of the end that goes into the booster is .792 and the GM one is much smaller. The perfect solution would be to find a nipple the is .792 on the booster side and .500 on the hose side but I don't know of any like that. Any ideas or suggestions for my dilemma? I don't know who makes my booster, it is a 8" dual diaphragm unit though.
|
|
|
|
03-05-2020, 12:00 PM
|
#2 |
|
Senior Member
 
Join Date: Jun 2007
Location: Pine Ridge Florida
Posts: 4,135
|
Re: Brake Booster Vacuum Hose Ideas
Something like this and hide it behind the intake? Could even heat shring over it to hide it more? They have every size you could think of.
https://www.fillernecksupply.com/1-2...t-gates-28609/
__________________
Click on my Not really a build thread, yet NOT SO RUST FREE RUST FREE BLAZER LS ENGINE SWAP INFORMATION THREAD BOLT RESTORATIONS 4l60 to an NP205 |
|
|
|
|
03-05-2020, 12:44 PM
|
#3 |
|
Post Whore
 
Join Date: May 2015
Location: Alabama
Posts: 14,671
|
Re: Brake Booster Vacuum Hose Ideas
yep...they sell similar ones at my local parts store
__________________
Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver |
|
|
|
|
03-05-2020, 03:07 PM
|
#4 |
|
Registered User
Join Date: Jun 2018
Location: Texas
Posts: 1,353
|
Re: Brake Booster Vacuum Hose Ideas
Looks like we may have the same booster. And it appears your missing the correct grommet. Here you go!
    
__________________
TA_C10 Stage 1 build - http://67-72chevytrucks.com/vboard/s....php?p=8333444 "It's only money". 
|
|
|
|
|
03-05-2020, 04:23 PM
|
#5 |
|
Registered User
Join Date: May 2012
Location: Faith,NC
Posts: 1,626
|
Re: Brake Booster Vacuum Hose Ideas
TA_C10, Our boosters look almost identical but the nipples are a little different.
I don't know if that grommet is big enough to fill the hole in my booster but I am certainly going to try it! It's worth a try for sure. Thanks! Last edited by Steve Cole; 03-05-2020 at 04:35 PM. |
|
|
|
|
03-05-2020, 05:24 PM
|
#6 |
|
Registered User
Join Date: Nov 2011
Location: Idaho
Posts: 857
|
Re: Brake Booster Vacuum Hose Ideas
Well it’s been almost 10 years for me and still works fine. I took Teflon tape and wrapped around the barbed end from booster to back of manifold to the thickness needed. Probably went a little larger then the inside diameter of the hose. Used a hose clamp. Can’t even see the Teflon tape inside if done right. Turned out clean.
|
|
|
|
|
| Bookmarks |
|
|
Hybrid Mode
