67 Factory Tach Cluster From C60 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**paulspickupparts** · 03-11-2020, 08:53 PM

Just ran across a 67 C60 that is going to the boneyard . I pulled this and hope to go back if still there. I did not have time to pull the harness or other parts. Just ran out of time. Truck was non running so no idea of function. There is a small scuff on the tach face.

I usually do not do much with 67-72 parts so wondering what its worth . Thanks

**68bowtie** · 03-11-2020, 11:22 PM

200-225?

**daddymoo2** · 03-12-2020, 08:30 AM

Interested in buying if you sell: But don’t know value. Was this a v8 or 6cylinder truck. Thanks Don

**paulspickupparts** · 03-12-2020, 10:10 AM

Right now I am looking for a value. This category has been getting a lot of flack for it being turned into a buy and selll category which it is not. If I can get an idea of its value I will create a new thread in the parts for sale category. . This was from a V8 truck .

**paulspickupparts** · 03-12-2020, 10:24 AM

Quote:

Originally Posted by daddymoo2

Interested in buying if you sell: But don’t know value. Was this a v8 or 6cylinder truck. Thanks Don

This was a V8 truck. Didn't you sell just just the tach only without gauges (6 Cyl ) for $150 . Are V-8 tachs worth more or less ? Also this should have an 80 pound oil pressure gauge that you have been selling. Thanks

**richard2717** · 03-18-2020, 08:41 AM

I sold several untested with 60lb gauges for $300 each. The 80lb should increase value a little if the face of the actual gauge is in good shape but the bezel may hurt value since it is a big truck bezel which is different from the C10-30 where the steering column goes thru. The speedo and fuel gauge may also have big truck idiot lights in them as well instead of the smaller truck versions

**paulspickupparts** · 03-18-2020, 11:22 AM

Thanks Richard . That gives me a good idea. I am going to clean it up a little and test some of the gauges. I am going to go back and get the harness for the tach and the ignition switch and door locks if they match. Hopefully it is not gone. It was being sold for scrap . UGH

**396ci** · 03-26-2020, 10:15 PM

the fuel gauge will have different wording on the red lenses than the c10-c30 trucks but will work just fine.

03-11-2020, 08:53 PM	#1
paulspickupparts Senior Member Join Date: Sep 2011 Location: Seward Nebraska Posts: 1,596	67 Factory Tach Cluster From C60 Just ran across a 67 C60 that is going to the boneyard . I pulled this and hope to go back if still there. I did not have time to pull the harness or other parts. Just ran out of time. Truck was non running so no idea of function. There is a small scuff on the tach face. I usually do not do much with 67-72 parts so wondering what its worth . Thanks Attached Images

03-11-2020, 11:22 PM	#2
68bowtie Senior Member Join Date: Jan 2007 Location: Turlock, CA Posts: 8,795	Re: 67 Factory Tach Cluster From C60 200-225? __________________ Please help my sister in law with her battle with cancer https://gofund.me/902f6fce Project "C10 Fever" (68 factory black 396 swb) Project "Little Sister" (70 c10 blue original paint refresh) Project "Blue Bomb" (70 c30 blue original paint refresh) SOLD Project "Vitamin C" (71 c10 orange original paint refresh) SOLD

03-12-2020, 08:30 AM	#3
daddymoo2 Senior Member Join Date: Mar 2010 Location: union,ky Posts: 1,575	Re: 67 Factory Tach Cluster From C60 Interested in buying if you sell: But don’t know value. Was this a v8 or 6cylinder truck. Thanks Don

03-12-2020, 10:10 AM	#4
paulspickupparts Senior Member Join Date: Sep 2011 Location: Seward Nebraska Posts: 1,596	Re: 67 Factory Tach Cluster From C60 Right now I am looking for a value. This category has been getting a lot of flack for it being turned into a buy and selll category which it is not. If I can get an idea of its value I will create a new thread in the parts for sale category. . This was from a V8 truck .

03-18-2020, 08:41 AM	#6
richard2717 Equal opportunity joke ofender Join Date: Oct 2011 Location: Eastern Shore of MD Posts: 10,128	Re: 67 Factory Tach Cluster From C60 I sold several untested with 60lb gauges for $300 each. The 80lb should increase value a little if the face of the actual gauge is in good shape but the bezel may hurt value since it is a big truck bezel which is different from the C10-30 where the steering column goes thru. The speedo and fuel gauge may also have big truck idiot lights in them as well instead of the smaller truck versions __________________ Members I have met. Dually Jams, OlBlue60, ScottH, Tommyboy24, Dujobo, Warbucket, 2003 Silverado, Notsolo, my90k5, 6t727t2, Special-K ,Jack_71C10, tabarcus,72blazer_mud_bogger,pwdcougar,RSavage,EricSean,1Rippen6,invicta455,tennaragtop71,arks, Kendal,Bennett68C10, Perpendicular, Chainsawman, McGeesCustomMinis,ShortbedClayton,longblue72,6768chevylover,Tim71,Travisarmenta,Ol' Drippy,fleetmitch,georgieb51,Dave,bcnya2,Dadsburb https://paypal.me/6772GMtruckparts Most women like the strong, silent type… Fortunately for me, my wife prefers the out-of-shape, mouthy type.

03-18-2020, 11:22 AM	#7
paulspickupparts Senior Member Join Date: Sep 2011 Location: Seward Nebraska Posts: 1,596	Re: 67 Factory Tach Cluster From C60 Thanks Richard . That gives me a good idea. I am going to clean it up a little and test some of the gauges. I am going to go back and get the harness for the tach and the ignition switch and door locks if they match. Hopefully it is not gone. It was being sold for scrap . UGH

03-26-2020, 10:15 PM	#8
396ci Senior Member Join Date: Jun 2005 Location: Modesto, CA Posts: 806	Re: 67 Factory Tach Cluster From C60 the fuel gauge will have different wording on the red lenses than the c10-c30 trucks but will work just fine. __________________ Brian XNGH ECV Chapter 58 1972 Jimmy / Blazer Project 2wd 1974 Chevy Crew Cab Shorty



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.