The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Suspension

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 04-29-2020, 04:36 PM   #1
my56chevytruck
Registered User
 
my56chevytruck's Avatar
 
Join Date: Feb 2016
Location: Hebron
Posts: 1,153
C NOTCH or no C NOTCH

A friend owns a 56 2nd Series Chevy truck and has asked me HOW MUCH C NOTCH can be done before reducing the stock height of the truck bed, so my question to you is, can you C NOTCH the rear frame without losing the stock height of your truck bed? AND have NO rear axle diff banging to bed issues?? those that have C notched your rear axle, can you post your pictures. thanks
__________________
RUBBER DOWN AND HIT THE ROAD!!!
1940 Ford Dlx Coupe
1969 Mach1

Last edited by my56chevytruck; 04-29-2020 at 04:52 PM.
my56chevytruck is offline   Reply With Quote
Old 04-29-2020, 05:25 PM   #2
Ziegelsteinfaust
Registered User
 
Join Date: Dec 2012
Location: Temple City
Posts: 3,628
Re: C NOTCH or no C NOTCH

There are 2 ways to do a C-notch, and total drop depends on a couple of factors.

Some cut the frame, and weld in the C about 1/2 to 2/3's of the frame height. The higher you cut the more reinforcement you will need.

To the above. Depending on how high the bed sits above the frame in that area. Its a good idea to weld thick wall square tube there to reinforce the span.

At ride height in my opinion for a cruiser you want 2" minimum between the top of you 3rd member, and bed floor. I prefer 3" for most builds.. My 2018 uses baby soft bump stops, and would find similar. Especially if you want to run really low.

I have built a truck with just over a 1" gap between the 3rd member, and bed floor. While usually not bad. Every once in a while it would be quite the ride. We put small RE5 airbags in back along with fill caps in the bumper to fill them up with a bicycle pump.
Ziegelsteinfaust is offline   Reply With Quote
Old 05-01-2020, 09:37 AM   #3
SCOTI
Registered User
 
SCOTI's Avatar
 
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,066
Re: C NOTCH or no C NOTCH

Quote:
Originally Posted by my56chevytruck View Post
A friend owns a 56 2nd Series Chevy truck and has asked me HOW MUCH C NOTCH can be done before reducing the stock height of the truck bed, so my question to you is, can you C NOTCH the rear frame without losing the stock height of your truck bed? AND have NO rear axle diff banging to bed issues?? those that have C notched your rear axle, can you post your pictures. thanks
He'll want 3" of clearance for a trouble free driving experience. 2" would get him by but it could occasionally make contact. Anything less than 2" is going to make contact sooner or later.

The more the frame gets notched, the weaker it gets so keep that in mind. Typical 'bolt-in' c-notches that remove 2/3 of the rail height are weaker than the stock rail despite having a thicker vertical area. Just welding in a 'C' (half pipe) is not as strong either. Like Ziegelsteinfaust suggested, if more than a 1/3 of the rail height is removed, the frame should be reinforced above the rail in some form/fashion.
__________________
67SWB-B.B.RetroRod
64SWB-Recycle
89CCDually-Driver/Tow Truck
99CCSWB Driver
All Fleetsides
@rattlecankustoms in IG

Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive.
It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar.....

Cubic inches is like Indiana Jones with a cheap pistol.
SCOTI is offline   Reply With Quote
Reply

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 09:58 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com