|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
04-24-2021, 09:13 PM
|
#1 |
|
Registered User
Join Date: May 2009
Location: Hazel Green AL
Posts: 286
|
What else do i need to make this steering wheel work?
I have a 87 that has a Grant steering wheel. I have never liked it. I got one from a 88-94.
How do i deal with making the horn work? The horn button has 2 spade terminals on it. What do i need and does both spades have to have a wire going to them? |
|
|
|
04-24-2021, 10:26 PM
|
#2 | |
|
Registered User
Join Date: Jun 2014
Location: Orlando Florida
Posts: 1,598
|
Re: What else do i need to make this steering wheel work?
You need the wire that inserts into that white part sticking out at the bottom. It has a plastic piece with nubs that lock it in like a bulb.
__________________
Quote:
|
|
|
|
|
|
04-25-2021, 09:21 AM
|
#3 |
|
Registered User
Join Date: May 2009
Location: Hazel Green AL
Posts: 286
|
Re: What else do i need to make this steering wheel work?
I have 2 male spades on horn button. So plug the new horn wire on one of the spades on the horn button. What goes to the other spade on the horn button?
|
|
|
|
|
04-25-2021, 10:23 AM
|
#4 |
|
Senior Member
Join Date: May 2004
Location: Caldwell,Tx.
Posts: 3,648
|
Re: What else do i need to make this steering wheel work?
Ground one terminal and hook the other to the original horn wire .
__________________
Born and proudly residing in a Red State ! |
|
|
|
|
04-25-2021, 12:16 PM
|
#5 | |
|
Registered User
Join Date: Jun 2014
Location: Orlando Florida
Posts: 1,598
|
Re: What else do i need to make this steering wheel work?
There is only one terminal. Your button is broken. The tab that holds the button on is broken.
__________________
Quote:
|
|
|
|
|
|
04-27-2021, 07:19 AM
|
#6 |
|
Registered User
Join Date: May 2009
Location: Hazel Green AL
Posts: 286
|
Re: What else do i need to make this steering wheel work?
Thanks, I see where mine is missing the little tab that goes to ground on steering wheel hub. Can i just put a small jumper wire from what is left of the tab to steering wheel hub?
Drill and thread hub for a ring wire terminal and use a female spade at button? |
|
|
|
|
04-27-2021, 11:46 AM
|
#7 | |
|
Registered User
Join Date: Jun 2014
Location: Orlando Florida
Posts: 1,598
|
Re: What else do i need to make this steering wheel work?
I didn't think the tab was a ground but I guess it does ground through the wheel with that tab. A wire will work.
__________________
Quote:
Last edited by Just call me Sean; 04-27-2021 at 11:52 AM. |
|
|
|
|
|
04-28-2021, 01:27 PM
|
#8 |
|
Senior Member
 
Join Date: Jun 2015
Location: Atlanta, GA.
Posts: 737
|
Re: What else do i need to make this steering wheel work?
I think you need one of these.
__________________
Jay Gesner Atlanta, GA 1985 C10 Long Bed 4X2 LS 5.3, 4L60E Father/Daughter Project |
|
|
|
|
04-28-2021, 04:41 PM
|
#9 |
|
Registered User
Join Date: Feb 2018
Location: Doland SD
Posts: 836
|
Re: What else do i need to make this steering wheel work?
If you wire up the ground then the horn will be one all the time. I uses that tab that's broke to contact the center bolt when pushed chosing the horn to go off. So wiring a ground to it would make the horn go off continuously.
__________________
 ( second times the charm) 71 gmc c15 307 sbc 373 rear gears positrac sm 465 trans. ( not listed on spid but is original )94 chevy k1500 350 tbi 373 rear gears 4l60e one wheel peel. Gutless 07 gmc sierra classic rcsb 4.3 lt 5 speed w/t 04 chevy Silverado 1500 ext cab 5.3 4l60e. 81 chevy Scottsdale k10 muncie sm465 Np208 10 bolt 8.2 ( Old Green) |
|
|
|
|
04-28-2021, 08:38 PM
|
#10 | |
|
Registered User
Join Date: Jun 2014
Location: Orlando Florida
Posts: 1,598
|
Re: What else do i need to make this steering wheel work?
No, the tab grounds to the steering wheel shaft. Pushing the button completes the circuit, completes the ground.
__________________
Quote:
|
|
|
|
|
|
| Bookmarks |
|
|
Hybrid Mode
