1965 Front Fender Mounting Plate "Grommets" Can't find any...

[RoyL]

Looked around the www and talked to truck shop, can't find any...
See photo. I have one missing. Probably can get something close but just want to ask here.



Sorry: can't post pic on mobile... will add it shortly. Fits inside this "plate"




Thx!
Roy

[jweb]

Like this:
https://www.classicparts.com/1960-66...iABEgKY7vD_BwE

[RoyL]

Originally Posted by jweb

Like this:
https://www.classicparts.com/1960-66...iABEgKY7vD_BwE

Thanks, I believe those goes where the inner fender mounts to the cab. From "inner shell mounting", section 11-13, view B, 1960-66 Factory assembly Manual. Part number lookup (3765905) came up with this, shows 4 however...? https://www.classicmuscle.com/p-1960...leeves-3765905

Will need those, cause I don't have any grommets there either...

I saw some that had a large washer and bolt that went with it, can't find it now, of course.

[joesscamaro]

I never knew there was supposed to be a grommet in there. Interesting.

[60-66]

This is a first , and I've taken apart some very low mile trucks. That grommet goes on the INNER fender bottom rear , not the bottom of a fender .

[RoyL]

Originally Posted by joesscamaro

I never knew there was supposed to be a grommet in there. Interesting.

Originally Posted by 60-66

This is a first , and I've taken apart some very low mile trucks. That grommet goes on the INNER fender bottom rear , not the bottom of a fender .

Well fellas, I can't say what's right here... there was a grommet on one fender and not on the other when I removed them... Based on the fairly large hole in the "fender mounting plate" it kinda made sense that something might be used to locate the lower fender bolt and cushion the fender from being metal to metal. Guy from Truck Shop said to use a 1955-59 chevy truck set that goes to the inner fender. PN 55-06501. http://www.truckandcarshop.com/trucks47_59/t47_056.html
They look pretty much like the inner fender to cab grommets linked above. Maybe we are talking past each other on the location, inner vs outer.

Appreciate the insight on what you've seen on other trucks!

[RoyL]

Originally Posted by RoyL

Well fellas, I can't say what's right here... there was a grommet on one fender and not on the other when I removed them... Based on the fairly large hole in the "fender mounting plate" it kinda made sense that something might be used to locate the lower fender bolt and cushion the fender from being metal to metal. Guy from Truck Shop said to use a 1955-59 chevy truck set that goes to the inner fender. PN 55-06501. http://www.truckandcarshop.com/trucks47_59/t47_056.html
They look pretty much like the inner fender to cab grommets linked above. Maybe we are talking past each other on the location, inner vs outer.

Appreciate the insight on what you've seen on other trucks!

Upon further inspection, the grommet that's there appears to be split to fit in there, did find the other one, it had fallen out and was in the 'bag and tag' box.

Here's photo of the hole, so from the factory, there was nothing used in here? I get you need some wiggle room for fender alignment, but this is a big hole. The aftermarket one I used the picture was from Truck Shop, that hole looks smaller than mine... hmmm. Oh well, I got what I got, so I'll put something similar back in there...

[f66]

Good Morning. Here are pictures of an original paint fender and mounting plate that have not been disassembled. Hard to determine if the mounting plate has a grommet.

[72Mountaineer]

Originally Posted by f66

Good Morning. Here are pictures of an original paint fender and mounting plate that have not been disassembled. Hard to determine if the mounting plate has a grommet.

Looks like no grommet, but a spacer for alignment.