Low mileage 350 in NJ - The 1947 - Present Chevrolet & GMC Truck Message Board Network

dpmalibu · 09-04-2005, 11:06 PM

I have a Jasper replacement motor I pulled from an 87 Monte Carlo SS. It only has 4500 miles according to the guy I bought it from. I have the reciept for the work that was done. Motor is bone stock and complete from intake manifold to oil pan . Motor has all emissions equipment on it. Only thing missing is the carb.Motor runs smooth and did not smoke or leak. Motor is extremely clean inside and out.Motor has center bolt valve covers. I looked up the serial # on the block and it comes up as 1988-94. Asking $675 B/O

I am located in Trenton,NJ

**crossy** · 09-09-2005, 05:48 PM

DP, does the two center bolts of the intake take the ones that go down in almost straight instead of the same angle as the others.
I'm sure you already know this but ALL 83-88 SS montes had 305's but you said you checked the numbrs as a 350 right.
DAVE

dpmalibu · 09-09-2005, 10:43 PM

Yes I know all Montes came with 305's. The guy I bought the car from told me he replaced it witha 350, plus it has 5.7 stamped on the back of the block and I also checked the numbers to make sure. The center 2 bolts are almost horizontal . The front and rear bolts are on an angle like all older SBCs. This is the era of the small block chevy that came right before the Vortec .The Vortec motor have the center 2 bolts on the manifold which are horizontal.Hopefully that clears things up for you. If you have any questions feel free to give me a call @ (609) 481-8811. Thanks

**crossy** · 09-16-2005, 11:50 AM

I'll pass that around. DAVE

dpmalibu · 09-17-2005, 03:09 PM

ttt

dpmalibu · 09-20-2005, 05:17 PM

Sold!!!!

09-04-2005, 11:06 PM	#1
dpmalibu Registered User Join Date: Dec 2004 Location: Hatboro,PA Posts: 367	Low mileage 350 in NJ $675 I have a Jasper replacement motor I pulled from an 87 Monte Carlo SS. It only has 4500 miles according to the guy I bought it from. I have the reciept for the work that was done. Motor is bone stock and complete from intake manifold to oil pan . Motor has all emissions equipment on it. Only thing missing is the carb.Motor runs smooth and did not smoke or leak. Motor is extremely clean inside and out.Motor has center bolt valve covers. I looked up the serial # on the block and it comes up as 1988-94. Asking $675 B/O I am located in Trenton,NJ Last edited by dpmalibu; 09-17-2005 at 03:12 PM.

09-09-2005, 05:48 PM	#2
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	DP, does the two center bolts of the intake take the ones that go down in almost straight instead of the same angle as the others. I'm sure you already know this but ALL 83-88 SS montes had 305's but you said you checked the numbrs as a 350 right. DAVE __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks.

09-16-2005, 11:50 AM	#4
crossy Oh,you can't buy that new Join Date: Apr 2000 Location: Pennsville,N.J. 08070, USA Posts: 2,039	I'll pass that around. DAVE __________________ "been there, done that, ruined the T-shirt". 2007 LBZ GMC Sierra, ECSB 2006 LM7 RCSB Silverado 98 Vortec project. 94,3500,6.5L 4L80 81 SWB GMC POS finally gone 73 Pinto, stock, w/CragarSS's-eww LOTS of Cummins trucks.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-09-2005, 10:43 PM	#3
dpmalibu Registered User Join Date: Dec 2004 Location: Hatboro,PA Posts: 367	Yes I know all Montes came with 305's. The guy I bought the car from told me he replaced it witha 350, plus it has 5.7 stamped on the back of the block and I also checked the numbers to make sure. The center 2 bolts are almost horizontal . The front and rear bolts are on an angle like all older SBCs. This is the era of the small block chevy that came right before the Vortec .The Vortec motor have the center 2 bolts on the manifold which are horizontal.Hopefully that clears things up for you. If you have any questions feel free to give me a call @ (609) 481-8811. Thanks

09-17-2005, 03:09 PM	#5
dpmalibu Registered User Join Date: Dec 2004 Location: Hatboro,PA Posts: 367	ttt

09-20-2005, 05:17 PM	#6
dpmalibu Registered User Join Date: Dec 2004 Location: Hatboro,PA Posts: 367	Sold!!!!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.