VIN number - cab swap - The 1947 - Present Chevrolet & GMC Truck Message Board Network

crosby · 10-17-2005, 09:33 AM

I just picked up a 77 K10 stepside, and hope to save the frame and build a decent driver for my plow truck. I looked on the dash where you usually see a vin and there is nothing there. Is the vin only on the door opening on the cab? I saw a plate there with a vin, but it has been painted over. I want to use the cab from my K20, but it's an 87, and I want to keep the truck pre-smog (1985 for NH) by running it as a 77, if possible. I know there are some sticky issues surrounding that

. Anyhow, is there supposed to be a vin plate on the dash? Did somebody maybe cover it up with a new dash or dash cover? Also looking for a cheap carb just to make the stepper run before I tear it apart. It is complete except for the carb. Thanks very much guys!

beaterC10 · 10-17-2005, 10:01 AM

The 77 cab I have only has the VIN on the door frame, nothing on the dash.

**Captkaos** · 10-17-2005, 04:40 PM

1973 - 1978 have the VIN in the door post ONLY. 1979- up have it displayed in the dash.

Bishops Trucks · 10-19-2005, 06:28 PM

edited by :Liz Buying and selling these on the site is strictly prohibited.

**N2TRUX** · 10-19-2005, 07:23 PM

Do you have a clean title for the 77? If you do, the truck can be registered as a 77 even if you run the 87 cab. The VIN is on the frame too. It will take a trip (or two) to your local DMV but it can be done....

Bishops Trucks · 10-19-2005, 08:32 PM

Sorry Liz, It won't happen again.

loblazer · 10-19-2005, 09:12 PM

Where on the frame is the vin Ken for a Blazer?

**N2TRUX** · 10-20-2005, 12:33 AM

Crap you would have to ask that. I haven't seen my Blazer in so long I don't remeber what it looks like. If I remember correctly it is on the drivers side close to the kick up in the front. Chris, Russell anyone want to confirm this....

Russell · 10-20-2005, 01:16 AM

My frame vin is on the outside of my passenger side rail. If I remember correctly, its right below the door. I had a hard time making it out till I wirebrushed it, then I was able to see it fairly clearly.

My frame is from a 79 GMC 3/4 ton 4x4, with my old 2wd 1980 cab sitting on top of it. I talked to the DMV about that, and they said it wasn't a problem so long as I had a bill of sale for both vehicles, which I do. No titles up here

The 80's frame was too rusty, the VIN musta flaked off, cause I never did find it.

**N2TRUX** · 10-20-2005, 08:54 AM

Quote:

Originally Posted by Russell

My frame vin is on the outside of my passenger side rail. If I remember correctly, its right below the door. .....

Ok, I was wrong on what side unless the Blazer is different. I still thought it was farther forward.....

Russell · 10-20-2005, 11:36 AM

I'll take a look this afternoon -- I'll actually have some time to get some stuff done before it gets dark and cold outside today, lol

loblazer · 10-20-2005, 07:45 PM

Thanks guys. Is it the same spot for all 73-91?

Doug

Russell · 10-20-2005, 09:50 PM

I don't quite think so...

I've heard of it being on the top of the frame rail for some vehicles, on the inside for others, or on the side like mine. Seems to be wherever the factory worker felt like putting it at that specific moment.

loblazer · 10-21-2005, 10:01 PM

OK I will look. I was told long time ago that it was on the drivers side back of the wheel and I could never find it. I probably should have just gone over the whole frame. I guess I will Sunday. Tougher now with paint on it.

Thanks guys, have a great weekend.

**N2TRUX** · 10-22-2005, 12:05 AM

Quote:

Originally Posted by loblazer

OK I will look. I was told long time ago that it was on the drivers side back of the wheel ......

Doug,
That's where I think it is on my 82 Blazer. Let me know if you find it....

loblazer · 11-01-2005, 02:18 PM

Just reading this reminded me I forgot to look. Wife has too many projects for me! haha

It is covered up and away for the winter in the garage but maybe I will try to get under it. Hard with a 5/5 drop though!

Doug

10-17-2005, 09:33 AM	#1
crosby Registered User Join Date: Aug 2004 Location: New Hampshire Posts: 437	VIN number - cab swap I just picked up a 77 K10 stepside, and hope to save the frame and build a decent driver for my plow truck. I looked on the dash where you usually see a vin and there is nothing there. Is the vin only on the door opening on the cab? I saw a plate there with a vin, but it has been painted over. I want to use the cab from my K20, but it's an 87, and I want to keep the truck pre-smog (1985 for NH) by running it as a 77, if possible. I know there are some sticky issues surrounding that . Anyhow, is there supposed to be a vin plate on the dash? Did somebody maybe cover it up with a new dash or dash cover? Also looking for a cheap carb just to make the stepper run before I tear it apart. It is complete except for the carb. Thanks very much guys! __________________ Crosby 1978 Chevrolet K10 stepside NH

10-17-2005, 10:01 AM	#2
beaterC10 Senior Member Join Date: Jul 2003 Location: Indianapolis, IN Posts: 1,277	Re: VIN number - cab swap The 77 cab I have only has the VIN on the door frame, nothing on the dash.

10-17-2005, 04:40 PM	#3
Captkaos www.73-87chevytrucks.com Join Date: Dec 1999 Location: Birmingham, AL Posts: 6,935	Re: VIN number - cab swap 1973 - 1978 have the VIN in the door post ONLY. 1979- up have it displayed in the dash. __________________ Chris Lucas 1973 Chevy C-10 1978 GMC Jimmy (2WD) - SOLD 1987 R10 twin turbo LS 1991 R3500 SRW CrewCab 1985 K5 diesel swapped project 1989 K5 2WD conversion w/ Vette susp Project Captkaos Customs 73-87chevytrucks.com

10-19-2005, 06:28 PM	#4
Bishops Trucks KEEP ON TRUCKIN' Join Date: Jun 2005 Location: Sterling, Va. Posts: 5,730	Re: VIN number - cab swap edited by :Liz Buying and selling these on the site is strictly prohibited. __________________ JIM '97 GMC Sierra K1500 '95 Chevy Silverado C1500 '71 Cheyenne Z71 / LT1 & 4-Speed SWB K/10 Father/Son Project http://www.youtube.com/watch?v=4l689JKXPnA http://67-72chevytrucks.com/vboard/payments.php "LIVIN' FREE FOREVER"

10-19-2005, 07:23 PM	#5
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	Re: VIN number - cab swap Do you have a clean title for the 77? If you do, the truck can be registered as a 77 even if you run the 87 cab. The VIN is on the frame too. It will take a trip (or two) to your local DMV but it can be done.... __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra" Last edited by N2TRUX; 10-19-2005 at 07:23 PM.

10-19-2005, 08:32 PM	#6
Bishops Trucks KEEP ON TRUCKIN' Join Date: Jun 2005 Location: Sterling, Va. Posts: 5,730	Re: VIN number - cab swap Sorry Liz, It won't happen again. __________________ JIM '97 GMC Sierra K1500 '95 Chevy Silverado C1500 '71 Cheyenne Z71 / LT1 & 4-Speed SWB K/10 Father/Son Project http://www.youtube.com/watch?v=4l689JKXPnA http://67-72chevytrucks.com/vboard/payments.php "LIVIN' FREE FOREVER"

10-19-2005, 09:12 PM	#7
loblazer Senior Member Join Date: Mar 2004 Location: Fergus, Ontario Posts: 481	Re: VIN number - cab swap Where on the frame is the vin Ken for a Blazer?

10-20-2005, 12:33 AM	#8
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	Re: VIN number - cab swap Crap you would have to ask that. I haven't seen my Blazer in so long I don't remeber what it looks like. If I remember correctly it is on the drivers side close to the kick up in the front. Chris, Russell anyone want to confirm this.... __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

10-20-2005, 01:16 AM	#9
Russell Professional Grade Join Date: May 2003 Location: Fort McMurray, Alberta Posts: 7,915	Re: VIN number - cab swap My frame vin is on the outside of my passenger side rail. If I remember correctly, its right below the door. I had a hard time making it out till I wirebrushed it, then I was able to see it fairly clearly. My frame is from a 79 GMC 3/4 ton 4x4, with my old 2wd 1980 cab sitting on top of it. I talked to the DMV about that, and they said it wasn't a problem so long as I had a bill of sale for both vehicles, which I do. No titles up here The 80's frame was too rusty, the VIN musta flaked off, cause I never did find it. __________________ 1995 Chevrolet 2 Door Tahoe (6.6L LBZ Duramax / ZF6 / NP241 with 1 ton solid axle swap) Last edited by Russell; 10-20-2005 at 01:17 AM.

10-20-2005, 11:36 AM	#11
Russell Professional Grade Join Date: May 2003 Location: Fort McMurray, Alberta Posts: 7,915	Re: VIN number - cab swap I'll take a look this afternoon -- I'll actually have some time to get some stuff done before it gets dark and cold outside today, lol __________________ 1995 Chevrolet 2 Door Tahoe (6.6L LBZ Duramax / ZF6 / NP241 with 1 ton solid axle swap)

10-20-2005, 07:45 PM	#12
loblazer Senior Member Join Date: Mar 2004 Location: Fergus, Ontario Posts: 481	Re: VIN number - cab swap Thanks guys. Is it the same spot for all 73-91? Doug

10-20-2005, 09:50 PM	#13
Russell Professional Grade Join Date: May 2003 Location: Fort McMurray, Alberta Posts: 7,915	Re: VIN number - cab swap I don't quite think so... I've heard of it being on the top of the frame rail for some vehicles, on the inside for others, or on the side like mine. Seems to be wherever the factory worker felt like putting it at that specific moment. __________________ 1995 Chevrolet 2 Door Tahoe (6.6L LBZ Duramax / ZF6 / NP241 with 1 ton solid axle swap)

10-21-2005, 10:01 PM	#14
loblazer Senior Member Join Date: Mar 2004 Location: Fergus, Ontario Posts: 481	Re: VIN number - cab swap OK I will look. I was told long time ago that it was on the drivers side back of the wheel and I could never find it. I probably should have just gone over the whole frame. I guess I will Sunday. Tougher now with paint on it. Thanks guys, have a great weekend.

11-01-2005, 02:18 PM	#16
loblazer Senior Member Join Date: Mar 2004 Location: Fergus, Ontario Posts: 481	Re: VIN number - cab swap Just reading this reminded me I forgot to look. Wife has too many projects for me! haha It is covered up and away for the winter in the garage but maybe I will try to get under it. Hard with a 5/5 drop though! Doug

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.