|
12-17-2005, 02:46 AM
|
#1 |
|
Broke and still trying
Join Date: Apr 2003
Location: Alameda, CA
Posts: 562
|
Zbar pivot bracket
Does anyone have pics of the pivot ball and bracket that mounts to the block? I'm looking for the correct one for my 1968 2wd. Mine looks weird and is very sloppy. It has a large bushing that fills the gap between the bracket to the zbar. It sits kind of low not at a 90* angle to the pivot point on the frame. My zbar may be incorrect also...no zerk fitting. Any pics or info would be greatly appreciated. This site has helped enourmously on my swap. Thanks in advance
|
|
|
|
12-17-2005, 05:52 PM
|
#2 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
Re: Zbar pivot bracket
I sure dont have a good pic on that bracket......is it a smallblock pc(block bracket)?
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
12-18-2005, 02:43 AM
|
#3 |
|
Broke and still trying
Join Date: Apr 2003
Location: Alameda, CA
Posts: 562
|
Re: Zbar pivot bracket
yes it's to a small block. I keep thinking maybe the zbar is too short. That's why they put a spacer in there. I mean the spacer I have is about an inch thick.
|
|
|
|
|
12-18-2005, 09:48 AM
|
#4 |
|
Fabricate till you "puke"
Join Date: Jun 2002
Location: Ill
Posts: 9,402
|
Re: Zbar pivot bracket
Can you post a pic of the Zbar & pivot ball?
__________________
69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears.... |
|
|
|
|
12-19-2005, 12:56 PM
|
#5 |
|
Questionable
Join Date: Mar 2005
Location: Atlanta
Posts: 13,373
|
Re: Zbar pivot bracket
I have a picture. Gimme a second.
__________________
If I've got anything up for grabs, it'll be here: 7-hole gauge cluster for a 67-72 p/u FREE (link) I can't check the forum daily. If I don't reply to you within 24 hours, drop me a PM! I'm (hopefully) still alive and will reply faster to a PM. |
|
|
|
|
12-19-2005, 01:02 PM
|
#6 |
|
Questionable
Join Date: Mar 2005
Location: Atlanta
Posts: 13,373
|
Re: Zbar pivot bracket
Here is a picture of the ball and the rag joint:
http://satellitehead.com/images/68ch...kage%20012.jpg I don't have a picture of hit hooked up readily available, but I bet you can find one in my gallery below - look at the "Inline Engine Swap" gallery (link to my gallery list: http://satellitehead.com/gallery ) in the and also any of the inline engine removal galleries. Might take a while, but I have a TON of pictures of this kind of stuff from my own experiences with building/rebuilding my truck....
__________________
If I've got anything up for grabs, it'll be here: 7-hole gauge cluster for a 67-72 p/u FREE (link) I can't check the forum daily. If I don't reply to you within 24 hours, drop me a PM! I'm (hopefully) still alive and will reply faster to a PM. |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
