Pictures of Aftermarket gauges installed in our trucks - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Low68 · 10-27-2002, 05:47 PM

here's another that I think looks a little better than mine.

jhow66 · 10-27-2002, 07:04 PM

Picture of my dash:

72futuresweet2wd · 10-29-2002, 10:38 AM

Does anybody have the gauges mounted to the bezel with just the glass of the gauges up against the opening? And if so how did you attach them to bezel? Any help would be appreciated.

Thanks

jhow66 · 10-29-2002, 02:59 PM

Here is how I mounted my tach and vac. gauge--hope you can see it good enough.

jay6891 · 10-29-2002, 05:15 PM

this is the one I want. While I'm wishing, I'll take the steering wheel also.

10-27-2002, 05:47 PM	#26
Low68 Registered User Join Date: May 2001 Location: Arizona Posts: 758	here's another that I think looks a little better than mine. Attached Images __________________ Build Thread

10-27-2002, 07:04 PM	#27
jhow66 Registered User Join Date: Jun 2002 Location: Knoxville Tenn. Posts: 3,058	Picture of my dash: Attached Images __________________ 56 Chevy Bel-Air 2dr. HT (purchased new) 71 Chevy Cheyenne SWB PU (502HO) 65 GMC short bed step--work in progress and my gofer

10-29-2002, 10:38 AM	#28
72futuresweet2wd The face of my 69 c10 Join Date: Jan 2001 Location: Central Indiana Posts: 171	Does anybody have the gauges mounted to the bezel with just the glass of the gauges up against the opening? And if so how did you attach them to bezel? Any help would be appreciated. Thanks __________________ 2002 Harley Davidson VRod 1972 2wd Blazer (Project) 1969 Chevy C10 (Driver) 2002 Chevy Trailblazer (Wifes)

10-29-2002, 02:59 PM	#29
jhow66 Registered User Join Date: Jun 2002 Location: Knoxville Tenn. Posts: 3,058	gauges Here is how I mounted my tach and vac. gauge--hope you can see it good enough. Attached Images __________________ 56 Chevy Bel-Air 2dr. HT (purchased new) 71 Chevy Cheyenne SWB PU (502HO) 65 GMC short bed step--work in progress and my gofer

10-29-2002, 05:15 PM	#30
jay6891 Car Knocker Join Date: May 2001 Location: jefferson,arkansas Posts: 664	this is the one I want. While I'm wishing, I'll take the steering wheel also. Attached Images __________________ 68 c-10,91 sportside bed,350 .030 over,4 bolt,10-1 comp,2.05 intake/1.94 exhaust,1.6 Harland Sharp roller rockers,edelbrock rpm cam and intake w/750 carb, 700r4, 3.73 gears,Jacabbs Electronic Igntion w/Accel HEI distributer and super coil. ZR-1 roll pan, filled tailights. Blazer tank. Hidden hitch. 2 1/2" Flowmaster 40's. Parts bought but not installed>> ford 9" posi with disc. CCP front and rear lowering kit 4/5. Cab corners,foor boards,rockers, cab braces, Phatom grill, Painless wiring kit.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.