Spindles to balljoints question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Spoof · 11-03-2002, 11:21 PM

I just popped in my new spindles, one side fits nicely without having to crank the lower balljoint nut down too tightly but the balljoint stud on the other side I really have to wrench the nut down to allow the cotter pin through. I haven't checked the torque specs yet but it seems the spindle is kind of stiff to turn, you can move it with one hand alright but I'm wondering how free the spindle should move back and forth? Any comments?

crazy longhorn · 11-04-2002, 12:01 AM

If the balljoints are new, the spindle should turn a little stiff. As they wear they tend to move a little easier. You might try a shot of grease & see how that feels. Also you might check to see that they arent rubbing on the top a arm....Im guessing dropped spindles. Good luck.....crazy AL

**COBALT** · 11-05-2002, 07:17 PM

Yeah, you should be able to turn the spindle with your hands, but it should be stiff. If one side is looser than the other then I'd examine it closely.

Are you sure you have your springs pocketed correctly? If one of them is misaligned it could be putting extra pressure on that lower control arm, and not letting you tighten that stud very much.

*Fast68Chevy* · 11-07-2002, 11:38 PM

what exactly did you do ? new spindles ? what you doing ?

good luck

11-03-2002, 11:21 PM	#1
Spoof Registered User Join Date: Jul 2000 Location: Victoria,BC, Canada Posts: 1,300	Spindles to balljoints question I just popped in my new spindles, one side fits nicely without having to crank the lower balljoint nut down too tightly but the balljoint stud on the other side I really have to wrench the nut down to allow the cotter pin through. I haven't checked the torque specs yet but it seems the spindle is kind of stiff to turn, you can move it with one hand alright but I'm wondering how free the spindle should move back and forth? Any comments? __________________ 71 GMC 1500 LWB

11-05-2002, 07:17 PM	#3
COBALT Senior Member Join Date: Sep 2001 Location: Seattle, WA, USA Posts: 5,817	Yeah, you should be able to turn the spindle with your hands, but it should be stiff. If one side is looser than the other then I'd examine it closely. Are you sure you have your springs pocketed correctly? If one of them is misaligned it could be putting extra pressure on that lower control arm, and not letting you tighten that stud very much. __________________ '69 3/4 ton C20 2wd-350ci/TH400 '69 3/4 ton Custom 20 2wd-350ci/4sp Manual '99 2wd 5.7 Chevy Tahoe Seattle, WA.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

11-04-2002, 12:01 AM	#2
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,402	If the balljoints are new, the spindle should turn a little stiff. As they wear they tend to move a little easier. You might try a shot of grease & see how that feels. Also you might check to see that they arent rubbing on the top a arm....Im guessing dropped spindles. Good luck.....crazy AL

11-07-2002, 11:38 PM	#4
Fast68Chevy Account Suspended Join Date: May 2000 Location: IL Posts: 0	what exactly did you do ? new spindles ? what you doing ? good luck



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.