i have a truck vid too! - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

79BIG10 · 01-28-2003, 05:11 AM

Took the time to download on dial up and sounds sweet

J-Spec C10 · 01-28-2003, 02:36 PM

Sounds great! What exhaust work do you have done?

MylilBowTie · 01-28-2003, 02:43 PM

Whats the recipe on the engine? Just wondering if its still gotta 305 or what not? I would hope it to be a 350.

low 84 · 01-28-2003, 05:14 PM

thanks for the compliments.

the engine is a 350 4 bolt, bored .06 over, dart iron eagle heads (2.02/1.60 w/200cc intake runners), 10:1 c.r., comp xe 262 cam, wiend intake and eddy carb. but this is only temporary, somthing a little better is going in this summer

the exhuast is dynomax ceramic coated shorty headers w/2.5 inch pipe to two 40 seires flows. and there are no tailpipes, it goes straight out of the mufflers. it had tailpipes but i cut them off because i thought they were hitting the axel.

01-28-2003, 05:11 AM	#26
79BIG10 I'm back with 2nd truck! Join Date: Feb 2002 Location: Texas Posts: 3,774	Took the time to download on dial up and sounds sweet __________________ 1979 Chevrolet Bonanza Big10 "Tootsie Roll" 1985 Chevrolet Silverado (wife's) Member of the Southern Bowties Club "Don't underestimate how sexy a fat man who drinks to excess can be." Homer Simpson

01-28-2003, 02:36 PM	#27
J-Spec C10 Whats this wire for?.... Join Date: Dec 2002 Location: Barrie, Ontario, CANADA Posts: 378	Sounds great! What exhaust work do you have done? __________________ Kyle CANADIAN CONNECTION '82 C10 Resto-Custom--> * 2 1/4" manifold back dual exhaust with Hooker Aerochambers & High Flow Cats Taylor Ignition Wires Centerline 15" Telstars with 32"x10" mudders

01-28-2003, 02:43 PM	#28
MylilBowTie Right turn Clyde Join Date: Nov 2002 Location: Cincinnati, Ohio Posts: 2,911	Whats the recipe on the engine? Just wondering if its still gotta 305 or what not? I would hope it to be a 350. __________________ 1974 C25 LWB: 454 4bbl Carb / TH400 / 3.73 1992 Camaro RS 305 TBI

01-28-2003, 05:14 PM	#29
low 84 Registered User Join Date: Jan 2002 Location: Houston, TX Posts: 2,144	thanks for the compliments. the engine is a 350 4 bolt, bored .06 over, dart iron eagle heads (2.02/1.60 w/200cc intake runners), 10:1 c.r., comp xe 262 cam, wiend intake and eddy carb. but this is only temporary, somthing a little better is going in this summer the exhuast is dynomax ceramic coated shorty headers w/2.5 inch pipe to two 40 seires flows. and there are no tailpipes, it goes straight out of the mufflers. it had tailpipes but i cut them off because i thought they were hitting the axel. __________________ '51 F100, backhalf with a narrowed 9 and coil overs, 18.5" mickeys, monte front clip, +400" sbc in the works '05 1500 Crew Cab RIP '84 swb 5/7 drop, solid cammed 408 w/ fully ported dart heads, th350 w/ 10 inch hughes, 12 bolt w/ 3.73 richmonds and a locker '80 swb 4x4 in progress: 7" lift, 350 th350/np205, d44 and 1.5" ORD tie rod, 14BFF w/discs , armored diff covers, 40" MTR's

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.