Z-ing a frame (REAR) - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Malibob · 06-08-2010, 07:33 PM

Can you z the rear of the frame? What I am thinking is right behind the cab before the bed mounts. Then right in front of the rear bed mounts. I can draw up a sketch but just wondering if it can be done and any ideas on how.

Steel plate and gussets is what I was thinking. Sketch coming tomorrow.

Alternatively, if I have to step notch instead, what do I do with my crossmember?

SCOTI · 06-08-2010, 07:52 PM

Yes, it can be done..... http://67-72chevytrucks.com/vboard/s...d.php?t=381425

Malibob · 06-08-2010, 09:36 PM

You sir are a bas ass! That is exactly what I was going for.

Malibob · 06-08-2010, 10:11 PM

Quote:

Originally Posted by SCOTI

Yes, it can be done..... http://67-72chevytrucks.com/vboard/s...d.php?t=381425

Why did you relocate your axles? Correct me if I am wrong, but, if I move the entire sections that holds the bed mounts, crossmember, shock mounts and springs couldnt I keep the stock setup and still drop the hell out of the truck? The only geometry changing would be the axle. Right? The added c-notch is an awesome idea too, I like the combination.

SCOTI · 06-08-2010, 11:45 PM

Quote:

Originally Posted by Malibob

Why did you relocate your axles? Correct me if I am wrong, but, if I move the entire sections that holds the bed mounts, crossmember, shock mounts and springs couldnt I keep the stock setup and still drop the hell out of the truck? The only geometry changing would be the axle. Right? The added c-notch is an awesome idea too, I like the combination.

Because even @ a 6-8" drop, the axle C/L shifts forward due to the geometry of the truck-arms. I just compensated for that & the additional drop allows for more travel/drop. I like the wheels centered or slightly to the rear on these trucks so I set it up w/some room for adjustment.

06-08-2010, 07:33 PM	#1
Malibob Registered User Join Date: May 2009 Location: Pittsburgh Posts: 392	Z-ing a frame (REAR) Can you z the rear of the frame? What I am thinking is right behind the cab before the bed mounts. Then right in front of the rear bed mounts. I can draw up a sketch but just wondering if it can be done and any ideas on how. Steel plate and gussets is what I was thinking. Sketch coming tomorrow. Alternatively, if I have to step notch instead, what do I do with my crossmember? __________________ This statement was made possible by a grant from this station and continued support from viewers like you. Flickr

06-08-2010, 07:52 PM	#2
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,068	Re: Z-ing a frame (REAR) Yes, it can be done..... http://67-72chevytrucks.com/vboard/s...d.php?t=381425 __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

06-08-2010, 09:36 PM	#3
Malibob Registered User Join Date: May 2009 Location: Pittsburgh Posts: 392	Re: Z-ing a frame (REAR) You sir are a bas ass! That is exactly what I was going for. __________________ This statement was made possible by a grant from this station and continued support from viewers like you. Flickr

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.