|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
08-10-2010, 11:21 PM
|
#1 |
|
Registered User
Join Date: Jan 2008
Location: HOUSTON TX
Posts: 1,161
|
upper control arm beveled pads
i was wondering where i can buy the beveled pads that go between the cross shaft and the shims for the upper control arm. gm has discontinued them and no dealers near me have them. the junkyard will not sell them seperate in fear that they will not be able to sell the complete crossmember. any help would be great. it is holding me up from having a roller. any help would be great, daniel.
|
|
|
|
08-10-2010, 11:40 PM
|
#2 |
|
BMW & ASE Master Certified
Join Date: Feb 2004
Location: Houston, Texas
Posts: 1,266
|
Re: upper control arm beveled pads
best bet is the pick-n-pull
__________________
1987 Silverado - L83 5.3 w/ 6L80e ,A/C,P/W,P/L,TILT, HID projectors, Wilwood C-10 Pro Spindles w/ 2018 silverado front brakes & C-5 Corvette Rear Disc Brakes 1999 BMW 528i - 5.7 LS1 w/ 4l60e, Ford 8.8 IRS w31 spline posi & FX-r projector retrofit New project: 2006 BMW x5 6cyl AWD to L83 6l80e 4wd to 2WD / RWD A poor man buy's it twice finally got my domain name back, 87chevy.com.... site rework in progress Last edited by 87chevy.com; 08-10-2010 at 11:40 PM. |
|
|
|
|
08-11-2010, 12:47 AM
|
#3 | |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,068
|
Re: upper control arm beveled pads
Quote:
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. Last edited by SCOTI; 08-11-2010 at 12:47 AM. |
|
|
|
|
|
08-11-2010, 08:12 AM
|
#4 |
|
Account Suspended
Join Date: Jun 2000
Location: over yonder
Posts: 14,270
|
Re: upper control arm beveled pads
I ran in to the same problem ... I made my own on a lathe.
|
|
|
|
|
08-13-2010, 02:35 AM
|
#5 |
|
Junior Member
Join Date: Jun 2006
Location: Pueblo,Colo
Posts: 424
|
Re: upper control arm beveled pads
if i can find them i'll give them to ya!! going to have to sell my project anyways so i rather see them get used then sitting in my grage for another 5yrs.
__________________
1968 LWB C10 "Project LADY EYE SORE" (She is my baby and sent me to the hospital 3 times for eye injuries lol  ) who said love hurts?? |
|
|
|
|
08-13-2010, 07:27 PM
|
#6 | |
|
Senior Member
Join Date: May 2004
Location: johnstown, NY
Posts: 2,393
|
Re: upper control arm beveled pads
Quote:
|
|
|
|
|
|
08-13-2010, 07:37 PM
|
#7 |
|
Registered User
Join Date: Jan 2008
Location: HOUSTON TX
Posts: 1,161
|
Re: upper control arm beveled pads
well since i had the arms together and already powdercoated i went ahead and got them from a vender that is on here. about 4 bucks a piece, not bad.
thanks for all the info again guys. daniel |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
