Has anyone repinned the ECU connectors? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

87chevy.com · 11-19-2010, 11:48 PM

Ive been wanting to finish the wiring on my truck for a long time. The wiring was stock length and just taped with electrical tape so it doesnt look bad... but its unfinished. My goal is to have shorten the harness down so theres not excess wire hanging around. Basically neaten it up. Cutting and splicing wires is not an option.
I probally should insert picture here, but I dont have one at the moment... I will take one tomarrow and update the post. Ive found the connectors on the net and they are not expensive, just unsure of the size... wire size of .35 is in mm or in? my guess is MM. I figure it would be easier to mod that one connector instead of the ones on the engine. I just want to clean up the wiring and cross one more thing off of the bucket list.
So has anyone one the board done this themselves?
clint

**TR65** · 11-20-2010, 12:40 AM

0.35 wire is metric gage, equivalent to 22 gage English.

TR

Shon · 11-21-2010, 05:48 PM

I have done some repinning, its not hard, just take your time.

11-19-2010, 11:48 PM	#1
87chevy.com BMW & ASE Master Certified Join Date: Feb 2004 Location: Houston, Texas Posts: 1,266	Has anyone repinned the ECU connectors? Ive been wanting to finish the wiring on my truck for a long time. The wiring was stock length and just taped with electrical tape so it doesnt look bad... but its unfinished. My goal is to have shorten the harness down so theres not excess wire hanging around. Basically neaten it up. Cutting and splicing wires is not an option. I probally should insert picture here, but I dont have one at the moment... I will take one tomarrow and update the post. Ive found the connectors on the net and they are not expensive, just unsure of the size... wire size of .35 is in mm or in? my guess is MM. I figure it would be easier to mod that one connector instead of the ones on the engine. I just want to clean up the wiring and cross one more thing off of the bucket list. So has anyone one the board done this themselves? clint __________________ 1987 Silverado - L83 5.3 w/ 6L80e ,A/C,P/W,P/L,TILT, HID projectors, Wilwood C-10 Pro Spindles w/ 2018 silverado front brakes & C-5 Corvette Rear Disc Brakes 1999 BMW 528i - 5.7 LS1 w/ 4l60e, Ford 8.8 IRS w31 spline posi & FX-r projector retrofit New project: 2006 BMW x5 6cyl AWD to L83 6l80e 4wd to 2WD / RWD A poor man buy's it twice finally got my domain name back, 87chevy.com.... site rework in progress

11-20-2010, 12:40 AM	#2
TR65 Senior Member Join Date: Nov 2007 Location: Greenville, SC Posts: 873	Re: Has anyone repinned the ECU connectors? 0.35 wire is metric gage, equivalent to 22 gage English. TR __________________ 1965 C10 SWB Fleet Two owner LS2 Swap Thread http://67-72chevytrucks.com/vboard/s...d.php?t=413880

11-21-2010, 05:48 PM	#3
Shon Registered User Join Date: Sep 2005 Location: sc Posts: 1,203	Re: Has anyone repinned the ECU connectors? I have done some repinning, its not hard, just take your time. __________________ 71 Cheyenne C10 LWB cam'd 6.0/T56 Swap

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.