|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
07-10-2011, 10:55 AM
|
#1 |
|
Registered User
Join Date: Jul 2011
Location: Pooler, Georgia
Posts: 20
|
230 to 350 swap pics please!!
Doin a engine swap in my 65 c10 from a 230 6 cylinder to a 350 with 3 speed would like to see some pics of the conversion THANKS
|
|
|
|
07-10-2011, 10:59 AM
|
#2 |
|
Registered User
Join Date: Dec 2009
Location: Orlando, Florida
Posts: 427
|
Re: 230 to 350 swap pics please!!
Jason, I'm about to do the same thing. What tranny are you going to use?
|
|
|
|
|
07-10-2011, 11:09 AM
|
#3 |
|
Registered User
Join Date: Jul 2011
Location: Pooler, Georgia
Posts: 20
|
Re: 230 to 350 swap pics please!!
I using the stock 3 speed manual. Needed some info on this swap i know it pretty simple and popular in these trucks.
|
|
|
|
|
07-11-2011, 12:51 AM
|
#4 |
|
60-66 Nut
  Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 23,252
|
Re: 230 to 350 swap pics please!!
Is there something specific you need to see?
__________________
Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE |
|
|
|
|
07-11-2011, 11:17 AM
|
#5 |
|
Registered User
Join Date: May 2011
Location: Lubbock, TX
Posts: 95
|
Re: 230 to 350 swap pics please!!
|
|
|
|
|
07-11-2011, 03:46 PM
|
#6 |
|
Registered User
Join Date: May 2011
Location: Lubbock, TX
Posts: 95
|
Re: 230 to 350 swap pics please!!
I used the stock 3spd. Used the flywheel/clutch/starter/mounts of the 230. Only thing I needed to buy for the swap was a Z-Bar pivot ball from NAPA. (make sure you have a pilot bushing in the V8 crankshaft) I did use an internal regulator alternator but I think you could use the one off the 6 if you extend the harness and have the correct brackets. Stock throttle linkage will need to be extended. I welded in a piece of allthread but couldn't get WOT so I switched to a cable throttle. Stock lower hose will work if you cut it. You'll need to run a 12v wire if you use an HEI distributor. Swap took a better part of a saturday but that was with me cleaning and throwing some paint on the firewall/inner fenders.
|
|
|
|
|
07-11-2011, 04:35 PM
|
#7 |
|
Registered User
Join Date: Sep 2010
Location: Tulsa, Oklahoma
Posts: 1,925
|
Re: 230 to 350 swap pics please!!
I have never done the 3 spd swap but I know you have to have some mounting points on your engine block for the linkage ? ask Capt fab about that ??
|
|
|
|
|
07-11-2011, 04:55 PM
|
#8 |
|
Registered User
Join Date: May 2011
Location: Lubbock, TX
Posts: 95
|
Re: 230 to 350 swap pics please!!
the stock 6cyl. Z-bar (bellcrank) will work you just need the pivot ball. The pivot screws into a threaded boss in the block.
|
|
|
|
|
07-11-2011, 05:19 PM
|
#9 |
|
Registered User
Join Date: Sep 2010
Location: Tulsa, Oklahoma
Posts: 1,925
|
Re: 230 to 350 swap pics please!!
I was not sure what it took when I put my 350 in so I just woosed out and put a 700r4 in so I would have overdrive , 3:73, 29" tire height , looking for 1900rpm and 70mph----I got it... and i did not need the pivot ball. Kieth
|
|
|
|
|
07-11-2011, 06:25 PM
|
#10 |
|
Registered User
Join Date: May 2011
Location: Lubbock, TX
Posts: 95
|
Re: 230 to 350 swap pics please!!
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
