Fuel system plumbing - The 1947 - Present Chevrolet & GMC Truck Message Board Network

C15_Sierra · 10-14-2011, 11:28 AM

I'm curious...do I need to install a 1-way check valve on the pressure (feed) side of the fuel rail? I'm not sure how much would readily fall back into the tank (I'm using an in-tank pump)

Is it more of a convenience or a necessity?

Thanks!

BR3W CITY · 10-14-2011, 01:38 PM

just seems like one more thing that can leak, clog, or fail. If my truck sits for a WHILE, I might have to key on for 2-3 seconds before cranking; however I do that anyway to hear the dbw throttle body cycle (just a habit, since i used to have problems with it).

clinebarger · 10-14-2011, 02:26 PM

The in-tank pump has a check valve built-in.

**TR65** · 10-14-2011, 09:12 PM

What Clinbarger says. My LS2 will hold full pressure for a couple of weeks normally.

TR

C15_Sierra · 10-14-2011, 09:17 PM

Cool, much appreciated guys!

C15_Sierra · 10-16-2011, 12:59 AM

OK another question -

What did you guys use for plumbing the fuel lines to the sender? Do the fuel rail quick connects work on the sender as well?

10-14-2011, 11:28 AM	#1
C15_Sierra Registered User Join Date: Apr 2011 Location: Hartford CT Posts: 223	Fuel system plumbing I'm curious...do I need to install a 1-way check valve on the pressure (feed) side of the fuel rail? I'm not sure how much would readily fall back into the tank (I'm using an in-tank pump) Is it more of a convenience or a necessity? Thanks! __________________ -Steve 1980 GMC C15 Sierra LWB Dark Carmine Red/Carmine Int Was: 250/3spd (1980-88), then a 305/TH350 (1988-2011) Now: 5.3/4L60E, 2.73 12-bolt open rear

10-14-2011, 01:38 PM	#2
BR3W CITY meowMEOWmeowMEOW Join Date: Sep 2009 Location: MKE WI Posts: 7,128	Re: Fuel system plumbing just seems like one more thing that can leak, clog, or fail. If my truck sits for a WHILE, I might have to key on for 2-3 seconds before cranking; however I do that anyway to hear the dbw throttle body cycle (just a habit, since i used to have problems with it). __________________ *'66 Short Step / SD Tuned / Big Cam LQ4 / Backhalfed /Built 4l80e / #REBUILDEVERYTHING* MY BUILD THE H8RDCPTR //\\ MY YOUTUBE CHANNEL REV J HD

10-14-2011, 02:26 PM	#3
clinebarger Senior Member Join Date: May 2009 Location: Fort Worth, TX Posts: 6,370	Re: Fuel system plumbing The in-tank pump has a check valve built-in.

10-14-2011, 09:12 PM	#4
TR65 Senior Member Join Date: Nov 2007 Location: Greenville, SC Posts: 873	Re: Fuel system plumbing What Clinbarger says. My LS2 will hold full pressure for a couple of weeks normally. TR __________________ 1965 C10 SWB Fleet Two owner LS2 Swap Thread http://67-72chevytrucks.com/vboard/s...d.php?t=413880

10-14-2011, 09:17 PM	#5
C15_Sierra Registered User Join Date: Apr 2011 Location: Hartford CT Posts: 223	Re: Fuel system plumbing Cool, much appreciated guys! __________________ -Steve 1980 GMC C15 Sierra LWB Dark Carmine Red/Carmine Int Was: 250/3spd (1980-88), then a 305/TH350 (1988-2011) Now: 5.3/4L60E, 2.73 12-bolt open rear

10-16-2011, 12:59 AM	#6
C15_Sierra Registered User Join Date: Apr 2011 Location: Hartford CT Posts: 223	Re: Fuel system plumbing OK another question - What did you guys use for plumbing the fuel lines to the sender? Do the fuel rail quick connects work on the sender as well? __________________ -Steve 1980 GMC C15 Sierra LWB Dark Carmine Red/Carmine Int Was: 250/3spd (1980-88), then a 305/TH350 (1988-2011) Now: 5.3/4L60E, 2.73 12-bolt open rear

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.