Will it fit? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

bigtruckboi2000 · 01-02-2012, 12:23 AM

Will a Edlebrock Performer manifold(part # EDL-2101) fit on my 350 SBC? I wanna use it to replace the Torquer II that's on it now and getting a real good deal on it. Here are some details on it-Edlebrock Performer Chevrolet Small Block Intake Manifold, Quadrajet flange & EGR Block. I have a Edlebrock 1406 600 cfm on it.

NCD1966 · 01-02-2012, 12:28 AM

Edelbrock 2101 Performer Series Intake Manifold
Fits 1955-1986, Chevrolet 262-400 cu. in. non-EGR V8s

check to see if your heads are 86 and older

bigtruckboi2000 · 01-02-2012, 12:43 AM

The plan is to run Dart heads(part # DRT-127221, summitt racing) with the performer manifold. The heads on the engine now are 305 heads(80-86 era) that are coming off once I get the dart heads and the performer manifold. The block is a standard 350 from the 68-79 era.

**Captainfab** · 01-02-2012, 01:51 AM

Yes it will bolt up to either heads.

bigtruckboi2000 · 01-02-2012, 08:47 AM

Will i need or have to change the carb? And what is EGR?
Posted via Mobile Device

NCD1966 · 01-02-2012, 09:04 AM

dont worry about EGR, sounds like you dont have it. exhaust gas recirculation, its a emission device that recirciates exhaust gas back into the engine.

Rich 5150 69 · 01-02-2012, 10:10 AM

Quote:

Originally Posted by bigtruckboi2000

Quadrajet flange & EGR Block. I have a Edlebrock 1406 600 cfm on it.

This is where you need to decide either quadrajet or elde carb, one is a spread bore the other eldbrock is square bore carb..get the correct manifold/carb.

bigtruckboi2000 · 01-02-2012, 10:22 AM

IMMA keep the edle 1406 carb to put on it. Will the performer be an improvement over the torker II 5001 that's on it now?
Posted via Mobile Device

NCD1966 · 01-02-2012, 10:52 AM

the Torker II is a single plane manifold and the Edelbrock Performer is a dual plane. A dual plane intake has a lower power band than a single plane. So if your looking for more low end power, this performer will help you in that department.

Torker II power band is 2,500-6,500 rpm

Performers power band is Idle-5,500 rpm

if you have a stock to mild cam you want the performer intake

bigtruckboi2000 · 01-02-2012, 11:32 AM

So the performer manifold it is. Thanks guys, your knowledge is invaluable!!!!
Posted via Mobile Device

01-02-2012, 12:23 AM	#1
bigtruckboi2000 Registered User Join Date: Apr 2011 Location: Camp Lejeune, NC Posts: 97	Will it fit? Will a Edlebrock Performer manifold(part # EDL-2101) fit on my 350 SBC? I wanna use it to replace the Torquer II that's on it now and getting a real good deal on it. Here are some details on it-Edlebrock Performer Chevrolet Small Block Intake Manifold, Quadrajet flange & EGR Block. I have a Edlebrock 1406 600 cfm on it. __________________ [B][I]1965 Chevy C10 SWB w/350(68-79), 305 H.O Heads, Edelbrock Performer 1406 600 cfm carb, Torquer II Manifold, AC Delco HEI, TH400, Flowmasters,3.07 gears 2005 GMC Yukon XL Denali w/Mangnaflow Exhaust 1983 Cutlass Supreme w/ 350, cam, Holley 650 cfm, Street Dominator intake, carb spacer, hydromatic, Flowmasters *Patriots always talk of dying for their country but never of killing for their country.*

01-02-2012, 12:28 AM	#2
NCD1966 Registered User Join Date: Jun 2010 Location: Lafayette , La Posts: 404	Re: Will it fit? Edelbrock 2101 Performer Series Intake Manifold Fits 1955-1986, Chevrolet 262-400 cu. in. non-EGR V8s check to see if your heads are 86 and older __________________ 1966 Chevy C10 Stepside 355ci sbc with 3speed OD 2021 GMC Sierra 1500 AT4 6.2 1980 Chevy Camaro z28 383ci 1990 Chevy Suburban 350 tbi 2x4 (sold) 1984 Chevy C10 sliverado short fleet 1997 Chevy C1500 short fleet

01-02-2012, 12:43 AM	#3
bigtruckboi2000 Registered User Join Date: Apr 2011 Location: Camp Lejeune, NC Posts: 97	Re: Will it fit? The plan is to run Dart heads(part # DRT-127221, summitt racing) with the performer manifold. The heads on the engine now are 305 heads(80-86 era) that are coming off once I get the dart heads and the performer manifold. The block is a standard 350 from the 68-79 era. __________________ [B][I]1965 Chevy C10 SWB w/350(68-79), 305 H.O Heads, Edelbrock Performer 1406 600 cfm carb, Torquer II Manifold, AC Delco HEI, TH400, Flowmasters,3.07 gears 2005 GMC Yukon XL Denali w/Mangnaflow Exhaust 1983 Cutlass Supreme w/ 350, cam, Holley 650 cfm, Street Dominator intake, carb spacer, hydromatic, Flowmasters *Patriots always talk of dying for their country but never of killing for their country.*

01-02-2012, 01:51 AM	#4
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: Will it fit? Yes it will bolt up to either heads. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

01-02-2012, 08:47 AM	#5
bigtruckboi2000 Registered User Join Date: Apr 2011 Location: Camp Lejeune, NC Posts: 97	Re: Will it fit? Will i need or have to change the carb? And what is EGR? Posted via Mobile Device __________________ [B][I]1965 Chevy C10 SWB w/350(68-79), 305 H.O Heads, Edelbrock Performer 1406 600 cfm carb, Torquer II Manifold, AC Delco HEI, TH400, Flowmasters,3.07 gears 2005 GMC Yukon XL Denali w/Mangnaflow Exhaust 1983 Cutlass Supreme w/ 350, cam, Holley 650 cfm, Street Dominator intake, carb spacer, hydromatic, Flowmasters *Patriots always talk of dying for their country but never of killing for their country.*

01-02-2012, 09:04 AM	#6
NCD1966 Registered User Join Date: Jun 2010 Location: Lafayette , La Posts: 404	Re: Will it fit? dont worry about EGR, sounds like you dont have it. exhaust gas recirculation, its a emission device that recirciates exhaust gas back into the engine. __________________ 1966 Chevy C10 Stepside 355ci sbc with 3speed OD 2021 GMC Sierra 1500 AT4 6.2 1980 Chevy Camaro z28 383ci 1990 Chevy Suburban 350 tbi 2x4 (sold) 1984 Chevy C10 sliverado short fleet 1997 Chevy C1500 short fleet

01-02-2012, 10:22 AM	#8
bigtruckboi2000 Registered User Join Date: Apr 2011 Location: Camp Lejeune, NC Posts: 97	Re: Will it fit? IMMA keep the edle 1406 carb to put on it. Will the performer be an improvement over the torker II 5001 that's on it now? Posted via Mobile Device __________________ [B][I]1965 Chevy C10 SWB w/350(68-79), 305 H.O Heads, Edelbrock Performer 1406 600 cfm carb, Torquer II Manifold, AC Delco HEI, TH400, Flowmasters,3.07 gears 2005 GMC Yukon XL Denali w/Mangnaflow Exhaust 1983 Cutlass Supreme w/ 350, cam, Holley 650 cfm, Street Dominator intake, carb spacer, hydromatic, Flowmasters *Patriots always talk of dying for their country but never of killing for their country.*

01-02-2012, 10:52 AM	#9
NCD1966 Registered User Join Date: Jun 2010 Location: Lafayette , La Posts: 404	Re: Will it fit? the Torker II is a single plane manifold and the Edelbrock Performer is a dual plane. A dual plane intake has a lower power band than a single plane. So if your looking for more low end power, this performer will help you in that department. Torker II power band is 2,500-6,500 rpm Performers power band is Idle-5,500 rpm if you have a stock to mild cam you want the performer intake __________________ 1966 Chevy C10 Stepside 355ci sbc with 3speed OD 2021 GMC Sierra 1500 AT4 6.2 1980 Chevy Camaro z28 383ci 1990 Chevy Suburban 350 tbi 2x4 (sold) 1984 Chevy C10 sliverado short fleet 1997 Chevy C1500 short fleet

01-02-2012, 11:32 AM	#10
bigtruckboi2000 Registered User Join Date: Apr 2011 Location: Camp Lejeune, NC Posts: 97	Re: Will it fit? So the performer manifold it is. Thanks guys, your knowledge is invaluable!!!! Posted via Mobile Device __________________ [B][I]1965 Chevy C10 SWB w/350(68-79), 305 H.O Heads, Edelbrock Performer 1406 600 cfm carb, Torquer II Manifold, AC Delco HEI, TH400, Flowmasters,3.07 gears 2005 GMC Yukon XL Denali w/Mangnaflow Exhaust 1983 Cutlass Supreme w/ 350, cam, Holley 650 cfm, Street Dominator intake, carb spacer, hydromatic, Flowmasters *Patriots always talk of dying for their country but never of killing for their country.*

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.