|
04-22-2012, 08:39 AM
|
#1 |
|
Registered User
Join Date: Nov 2010
Location: eau claire wisconsin
Posts: 8
|
Crossmember confusion
I have 78 k5 blazer stock suspension and a 3 in body lift, my question after trying for countless hours to find an answer is should my transmission crossmember be tight to the frame or spaced down just over an inch? The transfer case crossmember that is just behind it is tight to the frame, but the front crossmember is currently spaced.
Posted via Mobile Device
__________________
78 k5 blazer |
|
|
|
04-22-2012, 09:01 AM
|
#2 |
|
Registered User
Join Date: Nov 2010
Location: eau claire wisconsin
Posts: 8
|
Re: Crossmember confusion
He is a picture of what I currently have, I would like to know if I should take out the spacers, and mount it flush to the frame like the rear one or leave it where it is?
__________________
78 k5 blazer |
|
|
|
|
04-22-2012, 07:41 PM
|
#3 |
|
Registered User
Join Date: Nov 2010
Location: eau claire wisconsin
Posts: 8
|
Re: Crossmember confusion
The more I look at this the skid plate on the front crossmember looks bent down on the front edge, you can kind of see it in the picture, unfortunately for me driving around I only saw a two wheel drive blazer so I couldn't even compare it to see how mine should be, so if anyone has a 4x and wouldn't mind taking a look and letting me know, I would really appreciate it. Thank you
Posted via Mobile Device
__________________
78 k5 blazer |
|
|
|
|
04-22-2012, 08:10 PM
|
#4 |
|
Registered User
Join Date: Dec 2008
Location: Silverhill, Al
Posts: 2,026
|
Re: Crossmember confusion
I think my 4x4 burb was spaced down like that...
Posted via Mobile Device
__________________
Fuzzy Dice Club Member 87 Crew SWB Build for the crew http://67-72chevytrucks.com/vboard/s...d.php?t=430082 http://www.cardomain.com/ride/3232925 90 burb 2wd Build Thread For The Burb! http://67-72chevytrucks.com/vboard/s...d.php?t=383055 |
|
|
|
|
04-24-2012, 01:23 PM
|
#5 |
|
Registered User
Join Date: Nov 2010
Location: eau claire wisconsin
Posts: 8
|
Re: Crossmember confusion
Thank you for a reply, when I go to the pics of 4x4 blazers it looks like they are both spaced or neither are, but can't tell 100% if it is spaced and should not be, could that lead to issues? I know that drive shaft angle would be affect moving it up and down, could it lead to engine oil problems with the back down that far and the front then being pulled upward?
Posted via Mobile Device Posted via Mobile Device
__________________
78 k5 blazer |
|
|
|
|
04-24-2012, 06:20 PM
|
#6 |
|
Registered User
Join Date: May 2008
Location: Waukesha, WI
Posts: 904
|
Re: Crossmember confusion
Heres my 76, not spaced
__________________
70 stepside 76 blazer 86 Silverado 20 Max Trailering 6.2 Crew 71 Nova SS My Blazer build http://67-72chevytrucks.com/vboard/s...d.php?t=363634 |
|
|
|
|
04-30-2012, 02:11 AM
|
#7 |
|
Registered User
Join Date: Dec 2010
Location: freeburg, illinois
Posts: 885
|
Re: Crossmember confusion
from factory those spacers are installed on the top and the cross members sit flush with the frame rails as lifts were so common i can only assume then you just put them on the bottom, in my case it came on the bottom and put them back to factory to tilt my whole driveline up again then again that is on the newer trucks and i've never seen two crossmembers like that before so its somewhat out of my answerable range
__________________
1987 Chevy V30 - http://67-72chevytrucks.com/vboard/s...d.php?t=573854 1988 IROC-Z Camaro - 305/T5 T-Top 1989 GMC V35 - Marbolo Express http://67-72chevytrucks.com/vboard/s...d.php?t=596850 1991 V2500 Suburban Silverado - Sold 1991 V2500 Suburban Scottsdale - Big Nasty http://67-72chevytrucks.com/vboard/s...d.php?t=497423 2001 Ram 3500 5.9 H.O NV56 EC DRW - Sold 2003 1500 Silverado 2004 Ram 3500 5.9 H.O NV56 CC DRW - Sold 2005 Silverado 2500HD 6.6/ZF6 CC LWB |
|
|
|
|
04-30-2012, 08:58 PM
|
#8 |
|
Registered User
Join Date: May 2008
Location: Waukesha, WI
Posts: 904
|
Re: Crossmember confusion
You are correct about the spacers being on top of the frame, mine were.
__________________
70 stepside 76 blazer 86 Silverado 20 Max Trailering 6.2 Crew 71 Nova SS My Blazer build http://67-72chevytrucks.com/vboard/s...d.php?t=363634 |
|
|
|
|
05-03-2012, 06:50 AM
|
#9 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,851
|
Re: Crossmember confusion
Some guys move those spacers below the frame in an attempt to change the rear driveshaft angle. It's a weak way to go about it and also makes the front driveshaft angle worse.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
05-05-2012, 05:08 PM
|
#10 |
|
Registered User
Join Date: Nov 2010
Location: eau claire wisconsin
Posts: 8
|
Re: Crossmember confusion
I moved the spacers and everything looks better drive shaft angles, the distributor is spaced away from the fire wall and engine looks like it should thank you for the info guys
Posted via Mobile Device
__________________
78 k5 blazer |
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
