406 SBC, intake and carb FS - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Destructo · 09-24-2003, 09:41 PM

I have a 406 4 bolt main block that has been bored .030" over, hot tanked and painted, its ready to go together, also have the crank which needs to be ground because of rust that formed on it while the PO had it, rough looking heads but was told they should not be cracked, also the original pistons and rods. Rods look like they can be cleaned up and used again with some minor work. They are complete with valves 1.94 and 1.5 with 76cc chamber. The block is a '72 year. I'm asking $500 for the whole lot, also have the pushrods, a couple rusty chrome pulleys and a chrome timing cover.

Also have an edelbrock Torker 2 manifold, asking 50 for it. It came off a perfect running 350 that had less than 20k miles on a rebuild and was pulled because my friend needed something emissions legal.

Edelbrock 1406 carb that was working perfect when I took it off my truck and put a Holley 1460 on I had bought. I couldn't tell that there was anything wrong with it. I'm asking 75 for it.

Any of these prices are negotiable and I don't want to ship the engine, I will ship the carb and intake though.

I'm located in Lewisville NC 27012 email me at chad@martiansales.com or send me PM or just reply to this thread. I can get you pictures of any of the stuff if you want, just let me know. I will post them here or email them to you.

One last thing, if anybody is interested in a set of 10 bolt front and rear axles with 2.73 gears and a locking rear I will be swapping them out from under my truck soon.

Lynx · 09-24-2003, 11:00 PM

Where where you?/ where was i? with that carb and intake like 6 months ago!! i totaly could have used those on my old truck and gotten waaayyy more for it then i did ( couldnt fix the q-jet and didnt have time for a rebuid)

ohh well good luck

Ben

Destructo · 09-24-2003, 11:27 PM

Ahh well, If you know anybody looking for such items send um my way!

houston6 · 09-25-2003, 03:04 AM

i want the carb if you still have it

Destructo · 09-25-2003, 08:59 AM

Yep still have it, let me have your address and i'll let ya know what shipping is. You can email it to me if you like.

Actually I just noticed your in North Wilkesboro, if you want it you can come pick it up and look at it if you want.

79Chevypickup · 09-25-2003, 03:20 PM

Me too me too!!

I want the carb!!!

Destructo · 09-25-2003, 03:39 PM

Welp, first come first server. If I don't hear from him in awhile i'll let ya know. I have a Holley with manual choke, but it probably needs a rebuild, 600cfm vacuum secondaries.

houston6 · 09-26-2003, 12:51 PM

hey pm me with your number and ill call for directions so i can come down and get that carb

Destructo · 09-26-2003, 01:25 PM

Alright, i'm working at 5 tonight though. I'll be home tomorrow till around 3 probably.

Destructo · 09-28-2003, 01:51 PM

Carb is sold to houston 6 fellas. thx still have engine and intake.

09-24-2003, 09:41 PM	#1
Destructo Registered User Join Date: Sep 2003 Location: Lewisville, NC Posts: 1,836	406 SBC, intake and carb FS I have a 406 4 bolt main block that has been bored .030" over, hot tanked and painted, its ready to go together, also have the crank which needs to be ground because of rust that formed on it while the PO had it, rough looking heads but was told they should not be cracked, also the original pistons and rods. Rods look like they can be cleaned up and used again with some minor work. They are complete with valves 1.94 and 1.5 with 76cc chamber. The block is a '72 year. I'm asking $500 for the whole lot, also have the pushrods, a couple rusty chrome pulleys and a chrome timing cover. Also have an edelbrock Torker 2 manifold, asking 50 for it. It came off a perfect running 350 that had less than 20k miles on a rebuild and was pulled because my friend needed something emissions legal. Edelbrock 1406 carb that was working perfect when I took it off my truck and put a Holley 1460 on I had bought. I couldn't tell that there was anything wrong with it. I'm asking 75 for it. Any of these prices are negotiable and I don't want to ship the engine, I will ship the carb and intake though. I'm located in Lewisville NC 27012 email me at chad@martiansales.com or send me PM or just reply to this thread. I can get you pictures of any of the stuff if you want, just let me know. I will post them here or email them to you. One last thing, if anybody is interested in a set of 10 bolt front and rear axles with 2.73 gears and a locking rear I will be swapping them out from under my truck soon.

09-24-2003, 11:00 PM	#2
Lynx Registered User Join Date: Jun 2003 Location: Fort McMurray, Alberta, Canada Posts: 513	Where where you?/ where was i? with that carb and intake like 6 months ago!! i totaly could have used those on my old truck and gotten waaayyy more for it then i did ( couldnt fix the q-jet and didnt have time for a rebuid) ohh well good luck Ben __________________ Ben 1983 Silverado SWB 305 2002 Silverado Extended Cab 5.3 http://members.shaw.ca/bkennett

09-25-2003, 03:04 AM	#4
houston6 Registered User Join Date: May 2003 Location: north wilkesboro nc Posts: 221	i want the carb if you still have it __________________ Scott

09-25-2003, 08:59 AM	#5
Destructo Registered User Join Date: Sep 2003 Location: Lewisville, NC Posts: 1,836	Yep still have it, let me have your address and i'll let ya know what shipping is. You can email it to me if you like. Actually I just noticed your in North Wilkesboro, if you want it you can come pick it up and look at it if you want. Last edited by Destructo; 09-25-2003 at 09:01 AM.

09-25-2003, 03:20 PM	#6
79Chevypickup MY TRUCK IS FOR SALE!! Join Date: Sep 2003 Location: Pasadena, TX Posts: 292	Me too me too!! I want the carb!!! __________________ 1979 Chevy LWB 350ci / 700R4 Edelbrock under the hood F O R S A L E OR T R A D E

09-24-2003, 11:27 PM	#3
Destructo Registered User Join Date: Sep 2003 Location: Lewisville, NC Posts: 1,836	Ahh well, If you know anybody looking for such items send um my way!

09-25-2003, 03:39 PM	#7
Destructo Registered User Join Date: Sep 2003 Location: Lewisville, NC Posts: 1,836	Welp, first come first server. If I don't hear from him in awhile i'll let ya know. I have a Holley with manual choke, but it probably needs a rebuild, 600cfm vacuum secondaries.

09-26-2003, 12:51 PM	#8
houston6 Registered User Join Date: May 2003 Location: north wilkesboro nc Posts: 221	hey pm me with your number and ill call for directions so i can come down and get that carb __________________ Scott

09-26-2003, 01:25 PM	#9
Destructo Registered User Join Date: Sep 2003 Location: Lewisville, NC Posts: 1,836	Alright, i'm working at 5 tonight though. I'll be home tomorrow till around 3 probably.

09-28-2003, 01:51 PM	#10
Destructo Registered User Join Date: Sep 2003 Location: Lewisville, NC Posts: 1,836	Carb is sold to houston 6 fellas. thx still have engine and intake.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.