Project Vitamin C-10

[Solo2002]

This truck gets better every time I see it great work man
Posted via Mobile Device

[shortbed70]

Nice way to keep everything tidy! Bet you saved some money by crimping your own lines... Looking good man.
Posted via Mobile Device

[daverod]

Great work Alan always nice and clean.

[Alan's Classic]

Originally Posted by Solo2002

This truck gets better every time I see it great work man
Posted via Mobile Device

Originally Posted by shortbed70

Nice way to keep everything tidy! Bet you saved some money by crimping your own lines... Looking good man.
Posted via Mobile Device

Thanks, i'm sure came close to paying for the tool. I really don't know the cost of crimping fittings. I have heard it gets pricey.

Originally Posted by daverod

Great work Alan always nice and clean.

Thanks Dave, looks like your making some good progress on yours the last time I checked.

Took a 4 port plate and made it a three. It's not machinist quality, but not bad for a hand grinder. This fitting will go on the bottom of the inner fender to get the heater hoses thru and the low side hose from the compressor.

[Strodder]

Good idea Alan.

[Alan's Classic]

Originally Posted by Strodder

Good idea Alan.

A few things done tonight.

[Ta2Don]

Awesome idea and workmanship!!!
Posted via Mobile Device

[Strodder]

Looks great Did you check tire clearance turning lock to lock when on the ground? Just a thought. Lookin out for you.

[Solo2002]

Looks great hey I got a ? When you did your vent windows how did you get your glass to stay in mine slides in and out very easy I can't find the rubber that goes in the frame before the glass anywhere and I don't know what type of glue or sealant will hold it in seeing that you have done this and your work is great figured you were the one to ask ya know lol thanks
Posted via Mobile Device

[Alan's Classic]

Originally Posted by Ta2Don

Awesome idea and workmanship!!!
Posted via Mobile Device

I appreciate the comments Don.

Originally Posted by Strodder

Looks great Did you check tire clearance turning lock to lock when on the ground? Just a thought. Lookin out for you.

Thanks for the extra eye. I have not checked full lock to the left since I installed the 3 port fitting. I hope it's good. "praying". I did check full lock to the right. That's when i had some interferrence problems. Not sure if you saw that little uh oh.

Originally Posted by Solo2002

Looks great hey I got a ? When you did your vent windows how did you get your glass to stay in mine slides in and out very easy I can't find the rubber that goes in the frame before the glass anywhere and I don't know what type of glue or sealant will hold it in seeing that you have done this and your work is great figured you were the one to ask ya know lol thanks
Posted via Mobile Device

I was advised by several not to use sealant. Because if the glass ever gets broken you will play hell getting all the remnants out. I got some glass setting tape from my glass guy. It wasn't the easiest thing I have ever done. I don't cuss any more, but a few words almost slipped out getting mine to work. The tape I got from him was not thick enough. i took a piece and ripped it in half. It's hard to explain how I did this, but I will try. The tape wraps around the edge of the glass that is inserted in the channel. I used a soapy water solution in a spray bottle to ease installation. Using one piece is hard enough, but I installed the piece i ripped in half on one side of the glass. One side had one layer of tape and the other had two. Is it the right way to do it??? I don't know. So far it hasn't fallen out. Once I got it in place i finally got it too close with a little effort. I let it set for a week (a lttile overkill). I opened it and it seemed to be secure. I have yet to have them open going down the road. After I got the glass it place I used a razor to trim the excess tape.

I think LMC sells the tape or contact your local glass company. Take the parts with you.

[Solo2002]

Ok thanks man this clears up a lot.
Posted via Mobile Device

[Ta2Don]

Thanks for the info on the tape!

[Dinos63]

always such nice work!

[Alan's Classic]

Originally Posted by Solo2002

Ok thanks man this clears up a lot.
Posted via Mobile Device

Originally Posted by Ta2Don

Thanks for the info on the tape!

Y'all are welcome!!

Originally Posted by Dinos63

always such nice work!

Thanks Dino!! Much appreciated!!

I picked these moulded hoses up to install on the inside of the cab. Since I had to flip the 4 port bulkhead around I had to adjust my plans little.



It allowed me to install the heater hoses without kinking the hoses. I still need to install some hose clamps once I get them.



All hoses in place underneath.





Home made hose seperators.





Side view with tire in place.



Wheels full lock to the left. There is plenty of clearance. Still need 3 more fittings to finish top side.

[Ta2Don]

The hose routing is awesome and I especially like the zip-ties...

[Strodder]

Nice job Alan

[sdailey]

Nice work as usual buddy.

[theastronaut]

Very nice work Alan! On the glass setting tape, you did the right thing since it was a little loose with one layer and didn't have thicker tape. Its supposed to be tight, we usually have to use a special glass puller to get vents out of the frames and regulator tracks off. It is okay to use adhesive, but only at the ends-less than an inch on each end so the glass will come out later.

Also, I saw your want ad for bumper filler plates. Have you thought about just making a pair? The outer bent edges don't show once bolted up and it's easy to make the dimples with a ball bearing and socket. If you want to make your own I can send one of mine to uses as a pattern.


Posted via Mobile Device

[VA72C10]

Nice!

[Alan's Classic]

Originally Posted by Ta2Don

The hose routing is awesome and I especially like the zip-ties...

Thanks Don!! The zipties might be my temp solution for a while til I get everything operating. I've been looking for some nice hose seperators that will mount the hoses as well as seperate.

Originally Posted by Strodder

Nice job Alan

Thanks Dennis!!

Originally Posted by sdailey

Nice work as usual buddy.

Thanks Shannon!!

Originally Posted by theastronaut

Very nice work Alan! On the glass setting tape, you did the right thing since it was a little loose with one layer and didn't have thicker tape. Its supposed to be tight, we usually have to use a special glass puller to get vents out of the frames and regulator tracks off. It is okay to use adhesive, but only at the ends-less than an inch on each end so the glass will come out later.

Also, I saw your want ad for bumper filler plates. Have you thought about just making a pair? The outer bent edges don't show once bolted up and it's easy to make the dimples with a ball bearing and socket. If you want to make your own I can send one of mine to uses as a pattern.

Great tip on the adhesive. BTW thanks for the comments.

Yes I have thought about making some. I had two old sets somewhere. I can't seem to located them. Thanks for the offer. I might make a template from cardboard. If that doesn't work I'll let you know. There is a guy about 30 miles from me that has a set for sale. I might make the journey.

Originally Posted by VA72C10

Nice!

[bossmanivy]

Wow Alan, what a journey! I really enjoyed this build. I sure hope my truck turns out anything in the neighborhood of that nice. I just bought a 63 LWB that I plan to drive for awhile till I have my 69 done. I am 5 weeks sober, and I think your truck is stunning
Chris
Posted via Mobile Device

[Strodder]

Originally Posted by bossmanivy

I am 5 weeks sober, and I think your truck is stunning
Chris

ATTA BOY Chris.

[Alan's Classic]

Originally Posted by bossmanivy

Wow Alan, what a journey! I really enjoyed this build. I sure hope my truck turns out anything in the neighborhood of that nice. I just bought a 63 LWB that I plan to drive for awhile till I have my 69 done. I am 5 weeks sober, and I think your truck is stunning
Chris
Posted via Mobile Device

Thanks Chris for the kind comments. Congrats on the sobreity. Keep the faith and life will be awesome. It can beat you up every now and then, just don't drink. My truck was my drink, yes I wanted to give up one time. I didn't give up and I haven't taken that drink for 6.5 years.

I'm tuned into your build as well.

Don't take any short cuts or rush your build. Do it right the first time and it will elliminate headaches later on.

God Bless

[chevy_man5]

Originally Posted by bossmanivy

I am 5 weeks sober
Chris
Posted via Mobile Device

Keep up the good work Chris!

You too Alan!!

[flips72]

very nice, such clean work