adapting suburban bumper to pickup - The 1947 - Present Chevrolet & GMC Truck Message Board Network

wlarue72 · 10-25-2003, 12:47 PM

How hard is it to adapt a suburban bumper to fit a pickup. I found a great deal on an original bumper for a suburban, but noticed the frame is a little different than a pickup. Looks like it wouldn't be too difficult to fabricate. Anyone done this?

SCOTI · 10-25-2003, 01:49 PM

It only requires the inner truck bumper brackets for the sport style rear bumper. The burbs rear frame rail ends curl around & the bumper is bolted directly to the frame. Since the trucks frame rails are cut square they require a bracket that attaches to the inside of the frame rail & has the curve in the bracket that aligns w/the factory holes in the bumper.

I can prob get you the P/N for the brackets or you can order a pair from Chevy Duty (that's where I got mine).

wlarue72 · 10-25-2003, 02:35 PM

Thanks Scott, that's what I was thinking after doin a little research. Could you pm me about the place where you had yours rechromed. Thanks again, David

SCOTI · 10-25-2003, 03:24 PM

You have PM.

10-25-2003, 12:47 PM	#1
wlarue72 Registered User Join Date: Nov 2002 Location: DFW Texas Posts: 244	adapting suburban bumper to pickup How hard is it to adapt a suburban bumper to fit a pickup. I found a great deal on an original bumper for a suburban, but noticed the frame is a little different than a pickup. Looks like it wouldn't be too difficult to fabricate. Anyone done this? __________________ 72 Cheyenne Super 402 daily driver. A lifetime project!

10-25-2003, 01:49 PM	#2
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,068	It only requires the inner truck bumper brackets for the sport style rear bumper. The burbs rear frame rail ends curl around & the bumper is bolted directly to the frame. Since the trucks frame rails are cut square they require a bracket that attaches to the inside of the frame rail & has the curve in the bracket that aligns w/the factory holes in the bumper. I can prob get you the P/N for the brackets or you can order a pair from Chevy Duty (that's where I got mine). __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

10-25-2003, 02:35 PM	#3
wlarue72 Registered User Join Date: Nov 2002 Location: DFW Texas Posts: 244	Thanks Scott, that's what I was thinking after doin a little research. Could you pm me about the place where you had yours rechromed. Thanks again, David __________________ 72 Cheyenne Super 402 daily driver. A lifetime project!

10-25-2003, 03:24 PM	#4
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,068	You have PM. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.