|
12-01-2003, 12:22 AM
|
#1 |
|
Registered User
Join Date: Sep 2003
Location: Venedy, IL
Posts: 25
|
dana transfer case
Hey guys, I have a 70 blazer with a four spd manual and apparently a dana transfer case. Apparently, too much throttle snapped the output shaft. Does anyone have any info on these cases? Parts availability etc.. I don't know much about them. Would it be better to replace the shaft, or should I just look for a different transfer case? Thanks, Willie
__________________
1970 Blazer CST 350 700R4 |
|
|
|
12-01-2003, 02:42 AM
|
#2 |
|
Registered User
Join Date: Feb 2003
Location: The Rubber City
Posts: 5,498
|
What engine do you have?
Transfer case is a Dana 20, and IIRC they are fairly common transfers, not in Blazers but more so in Jeeps and maybe Scouts. Good luck.
__________________
1969 GMC K2500  1996 Honda Accord 2007 Kawasaki KLR 650 |
|
|
|
|
12-01-2003, 10:04 AM
|
#3 |
|
Registered User
Join Date: Sep 2003
Location: Venedy, IL
Posts: 25
|
I have got a 350. Thanks for the info. If anyone has this output shaft, or has any other suggestions, I'd appreciate the advice. Thanks, Willie
__________________
1970 Blazer CST 350 700R4 |
|
|
|
|
12-01-2003, 10:49 PM
|
#4 |
|
Registered User
Join Date: Jun 2003
Location: s.e. tenn
Posts: 28
|
Dana t-case
I have 2 Dana 20's. I used to have one in my Blazer. I replaced it with a 4-speed 205. So a Dana 20 will also bolt up to a 4-speed? Cause I thought they just came behind 3-speed manuals. Is the transmission to T-case adapter the same for all manuals? Sorry to butt in on your post.
|
|
|
|
|
12-01-2003, 10:52 PM
|
#5 |
|
Registered User
Join Date: Sep 2003
Location: Venedy, IL
Posts: 25
|
I also read that the dana's were only behind a 3 spd, but apparently they also were with the four spd with granny low. What did you have to change when you put in your 205, blazomatic?
__________________
1970 Blazer CST 350 700R4 |
|
|
|
|
12-01-2003, 11:38 PM
|
#6 |
|
Registered User
Join Date: Jun 2003
Location: s.e. tenn
Posts: 28
|
Nothing. I lucked up and found a guy that had the whole set up for sale in the local paper. He rolled his '71. I got the trans, t-case, cross members, shifters and all. I took my 3-speed out and put in the four speed. I used my 3-speed cross member cause it was in better shape. My drive shafts worked. From what I've heard the Dana 20 was fairly common in 4x4 Blazers. Behind the 6 cyclinders and the 307 (like I have). Another member has the 3-speed and Dana 20 for sale $100 I think. I have one I would get rid of but I'm kinda far away. You could probably find one closer.
|
|
|
|
|
12-02-2003, 12:07 AM
|
#7 |
|
Registered User
Join Date: Sep 2003
Location: Venedy, IL
Posts: 25
|
Thanks for the info, blazomatic. I'm not sure what I'm going to do, I have been thinking about putting an auto in it sometime anyway, this might have forced my hand. I have a parts truck with a TH350 and NP203 so I might try to stick that in. It is good to know that a 205 might fit behind the 4spd without changing driveshafts though. Thanks again- Willie
__________________
1970 Blazer CST 350 700R4 |
|
|
|
|
12-02-2003, 05:07 PM
|
#8 |
|
Account Suspended
Join Date: Oct 2003
Location: texas
Posts: 199
|
i have a dana i will part with out of jimmy with 350 moter for $100.00 + shipping pm me if interested
|
|
|
|
|
12-02-2003, 10:23 PM
|
#9 |
|
Chevelle Nutt
Join Date: Nov 2002
Location: Fredericksburg, Va.
Posts: 204
|
blazomatic, what are you asking for the Dana 20? I'm in northern va.
Doug
__________________
71 CST Blazer 4X4, 350, on da tree  81 Blazer 2wd 350 350 99 F*** Ranger, I know, I know but it's cheap transportation  83 Mustang GT 5.0 4 speed loaded "got cubic inch?"
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
