|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
12-15-2015, 01:02 PM
|
#1 |
|
Registered User
Join Date: Mar 2013
Location: indiana
Posts: 18
|
Any thoughts on how low?
I have a 1987 Chevy shorty, I have lowered it 3" in front with springs. I am thinking about 3" more with spindles. Will this be to low to drive? I did a rear end flip as well, back is lower than front as of now. Any thoughts?
|
|
|
|
12-15-2015, 02:45 PM
|
#2 |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,068
|
Re: Any thoughts on how low?
They can be driven @ that height but will make contact with the road. How fast you're going & how solid the irregularity in the road surface will determine the extent (if any) of damage done.
For daily driving, you'll want the front x-member farther from the road surface which means more extensive mods.
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
|
12-15-2015, 10:09 PM
|
#3 |
|
Diggin The SquareLife
Join Date: Dec 2010
Location: garland,tx
Posts: 1,933
|
Re: Any thoughts on how low?
go with 2.5 western chassis spindles.....6" would be to low
|
|
|
|
|
12-16-2015, 02:12 PM
|
#4 |
|
Registered User
Join Date: Jul 2009
Location: San Jose Ca
Posts: 2,871
|
Re: Any thoughts on how low?
How tall of a tire are you running? You might be fine with ground clearance on a 30 inch tire (but will have fender clearance issues) vs a 26 inch tire.
__________________
David Used parts build: http://67-72chevytrucks.com/vboard/s...d.php?t=638991 My brother's Nova: http://www.67-72chevytrucks.com/vboa...d.php?t=727985 Rear suspension rework: http://www.67-72chevytrucks.com/vboa...d.php?t=750557 Instagram: myfabguy |
|
|
|
|
12-18-2015, 11:30 PM
|
#5 |
|
Square
Join Date: Feb 2011
Location: Phoenix Arizona
Posts: 1,568
|
Re: Any thoughts on how low?
x2 on what SCOTI said, if you want to go that low on a daily you will really want to look into raising the front crossmember. PB is your best bet.
__________________
Squarebody Syndicate |
|
|
|
|
12-19-2015, 02:08 AM
|
#6 |
|
meowMEOWmeowMEOW
Join Date: Sep 2009
Location: MKE WI
Posts: 7,128
|
Re: Any thoughts on how low?
I have a different truck, so its not a direct comparison, but I drive mine on a ~4.5/6" drop and never ran into much of an issue bottoming out. I wouldn't even consider it all that low with a mid-profile 15" tire.
__________________
'66 Short Step / SD Tuned / Big Cam LQ4 / Backhalfed /Built 4l80e / #REBUILDEVERYTHING  |
|
|
|
|
12-19-2015, 02:38 AM
|
#7 | |
|
Registered User
Join Date: Apr 2001
Location: DALLAS,TX
Posts: 22,068
|
Re: Any thoughts on how low?
Quote:
__________________
67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... Cubic inches is like Indiana Jones with a cheap pistol. |
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
\\ MY YOUTUBE CHANNEL
Linear Mode
