|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
06-21-2019, 09:58 AM
|
#1 |
|
Registered User
Join Date: May 2010
Location: St.Louis
Posts: 644
|
Speed Engineering longtubes lowered
Ive done a few searches, but havent quite found a shot of a lowered C10 with the speed engineering long tubes.
I'm 4/6 ECE, and my old sbc with doug thorleys were well below the frame. My concern is pulling the trigger on the 1 3/4 LT from them. If they dont fit, its 20% restock. I'm fairly certain the shorties/mid will fit with minor alterations. I would much rather have the LT's. Anyone 3/5 or 4/6 drop have any pics? Thanks! |
|
|
|
06-21-2019, 11:11 AM
|
#2 |
|
Almost Satisfied
 
Join Date: Mar 2002
Location: Springfield, MO
Posts: 2,932
|
Re: Speed Engineering longtubes lowered
I have the 4/6 ECE drop and the long tubes. You will have no issues.
__________________
1971 C10 Stepside. LSx 6.0 with BTR Stage IV, Speed Engineering Headers, 4L80e transmission w/3200 Circle-D Stall. 3.73. Posi. Purchased this truck when I was 17. I started the rebuild (or take apart) in 1993. I have drug it around all over the country in pieces. Finally back on the road in 2021. "I can't complain, but sometimes I still do. Life's been good to me so far." |
|
|
|
|
06-21-2019, 12:52 PM
|
#3 | |
|
Registered User
Join Date: May 2010
Location: St.Louis
Posts: 644
|
Re: Speed Engineering longtubes lowered
Quote:
How about your mounts? I'm running CPP adjustables with their mounts. |
|
|
|
|
|
06-21-2019, 10:44 PM
|
#4 |
|
Registered User
Join Date: Apr 2014
Location: Azle,Texas
Posts: 2,248
|
Re: Speed Engineering longtubes lowered
Sorry no pics at the moment but my 72 has the long tubes and they tuck up very high. 1971Stepside picture accurately depicts what I have.
__________________
Brian 1972 C10, "Loyd", LWB to SWB, 5.3, L83/6L80e, 4:11 Tru Trac, Air Ride, VA, DD, 20" Coys, 4 wheel disc, A quick LS swap turned into a 6 year frame off resto-mod. |
|
|
|
|
06-21-2019, 11:15 PM
|
#5 | |
|
Registered User
Join Date: May 2010
Location: St.Louis
Posts: 644
|
Re: Speed Engineering longtubes lowered
L
Quote:
Coincidence? Not sure. But if they dont hang below the frame rails I'm pulling the trigger For the record these are the 1 3/4? Not 1 7/8 shouldn't really matter but curious |
|
|
|
|
|
06-25-2019, 05:22 PM
|
#6 |
|
Almost Satisfied
Join Date: Mar 2002
Location: Springfield, MO
Posts: 2,932
|
Re: Speed Engineering longtubes lowered
I'm running the POL stands on my application.
__________________
1971 C10 Stepside. LSx 6.0 with BTR Stage IV, Speed Engineering Headers, 4L80e transmission w/3200 Circle-D Stall. 3.73. Posi. Purchased this truck when I was 17. I started the rebuild (or take apart) in 1993. I have drug it around all over the country in pieces. Finally back on the road in 2021. "I can't complain, but sometimes I still do. Life's been good to me so far." |
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
