Door alignment question - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**Hart_Rod** · 04-19-2021, 12:11 PM

My driver side door is out of alignment, (it hangs low at the rear of the door. The hinges are good and the striker is new). I need to loosen the lower hinge where it bolts to the cab so I can move the door to the rear. My main question is, can this be done without removing the fender or is that the only way? TIA

71gmcC15 · 04-19-2021, 12:43 PM

Yes you can just take the door off.

**Hart_Rod** · 04-19-2021, 01:48 PM

Quote:

Originally Posted by 71gmcC15

Yes you can just take the door off.

I was trying to avoid doing that, but looks like that is my only option.

**TKCR** · 04-19-2021, 07:35 PM

You can do it with the door on, I did. I had taken my doors off to replace the hinge with new ones. Then of course the doors needed adjustments. I was adjusting just about everything. The hinge bolts to the fender, hinge bolts to the door and the striker bolt. I finally got it right. The doors close very nice now, and they the lines look good and flush.

**Hart_Rod** · 04-19-2021, 08:07 PM

Quote:

Originally Posted by TKCR

You can do it with the door on, I did. I had taken my doors off to replace the hinge with new ones. Then of course the doors needed adjustments. I was adjusting just about everything. The hinge bolts to the fender, hinge bolts to the door and the striker bolt. I finally got it right. The doors close very nice now, and they the lines look good and flush.

I ended up shimming the bottom hinge about 1/16th of an inch and it worked perfect!

**TKCR** · 04-19-2021, 09:00 PM

Quote:

Originally Posted by Hart_Rod

I ended up shimming the bottom hinge about 1/16th of an inch and it worked perfect!

72c20customcamper · 04-20-2021, 09:25 AM

With these trucks these wrenches are invaluable. But in SAE

**Hart_Rod** · 04-20-2021, 11:15 AM

Quote:

Originally Posted by 72c20customcamper

With these trucks these wrenches are invaluable. But in SAE

Where do you purchase those?

**Palf70Step** · 04-20-2021, 05:11 PM

Amazon has them
https://www.amazon.com/gp/product/B0...KIKX0DER&psc=1

**TKCR** · 04-20-2021, 07:56 PM

Wished I would have know about these. I made due, but this could have made the job a bit easier.

**Hart_Rod** · 04-21-2021, 09:05 AM

Quote:

Originally Posted by Palf70Step

Amazon has them
https://www.amazon.com/gp/product/B0...KIKX0DER&psc=1

Thanks Bill!

Quote:

Originally Posted by TKCR

Wished I would have know about these. I made due, but this could have made the job a bit easier.

100%

72c20customcamper · 04-21-2021, 10:03 AM

I got them on Amazon but I also have a few box end wrenches I put a vise heated and bent them .

04-19-2021, 12:11 PM	#1
Hart_Rod ************* Join Date: Apr 2005 Location: Pensacola, FL Posts: 17,862	Door alignment question My driver side door is out of alignment, (it hangs low at the rear of the door. The hinges are good and the striker is new). I need to loosen the lower hinge where it bolts to the cab so I can move the door to the rear. My main question is, can this be done without removing the fender or is that the only way? TIA __________________ Rob - https://www.instagram.com/hart_rod_c10 As Iron Sharpens Iron, So One Man Sharpens Another. Proverbs 27:17 FOR SALE: DBW pedal bracket - http://67-72chevytrucks.com/vboard/s...d.php?t=651123 FOR SALE: Hood Brackets http://67-72chevytrucks.com/vboard/s...d.php?t=679945 1987 Silverado SWB - 34.5K original miles http://67-72chevytrucks.com/vboard/s...d.php?t=801834 1969 SuperBurb - http://67-72chevytrucks.com/vboard/s...d.php?t=200387 1968 Farm truck - http://67-72chevytrucks.com/vboard/s...d.php?t=358692 1968 SWB - http://67-72chevytrucks.com/vboard/s...d.php?t=551258 1948 Chevy - http://67-72chevytrucks.com/vboard/s...=122164&page=3

04-19-2021, 12:43 PM	#2
71gmcC15 Registered User Join Date: Feb 2018 Location: Doland SD Posts: 836	Re: Door alignment question Yes you can just take the door off. __________________ ( second times the charm) 71 gmc c15 307 sbc 373 rear gears positrac sm 465 trans. ( not listed on spid but is original ) 94 chevy k1500 350 tbi 373 rear gears 4l60e one wheel peel. Gutless 07 gmc sierra classic rcsb 4.3 lt 5 speed w/t 04 chevy Silverado 1500 ext cab 5.3 4l60e. 81 chevy Scottsdale k10 muncie sm465 Np208 10 bolt 8.2 ( Old Green)

04-19-2021, 07:35 PM	#4
TKCR Senior Member Join Date: Oct 2014 Location: Ohio Posts: 6,983	Re: Door alignment question You can do it with the door on, I did. I had taken my doors off to replace the hinge with new ones. Then of course the doors needed adjustments. I was adjusting just about everything. The hinge bolts to the fender, hinge bolts to the door and the striker bolt. I finally got it right. The doors close very nice now, and they the lines look good and flush. __________________ FB Page for my Seats Belts https://www.facebook.com/73-87-Chevy...9439407476735/ Restoring Seatbelts: http://67-72chevytrucks.com/vboard/s...d.php?t=809750 SOLD My 86 Build:http://67-72chevytrucks.com/vboard/s...d.php?t=654972 Past Restored Bench Seats:http://67-72chevytrucks.com/vboard/s...d.php?t=715398 PayPal link to pay for your items: https://www.paypal.me/TKCR

04-20-2021, 09:25 AM	#7
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,765	Re: Door alignment question With these trucks these wrenches are invaluable. But in SAE Attached Images __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

04-20-2021, 05:11 PM	#9
Palf70Step State of Confusion! Join Date: Jul 2002 Location: Gulfport, MS USA Posts: 47,269	Re: Door alignment question Amazon has them https://www.amazon.com/gp/product/B0...KIKX0DER&psc=1 __________________ Bill 1970 Chevy Custom/10 LWB Fleetside 2010 Toyota Tacoma PreRunner SR5 Double Cab - DD Member of Louisiana Classic Truck Club (LCTC) Bill's Gallery Life isn't tied with a bow, but it's still a gift. Live simply. Love generously. Care deeply. Speak kindly. Leave the rest to God!

04-20-2021, 07:56 PM	#10
TKCR Senior Member Join Date: Oct 2014 Location: Ohio Posts: 6,983	Re: Door alignment question Wished I would have know about these. I made due, but this could have made the job a bit easier. __________________ FB Page for my Seats Belts https://www.facebook.com/73-87-Chevy...9439407476735/ Restoring Seatbelts: http://67-72chevytrucks.com/vboard/s...d.php?t=809750 SOLD My 86 Build:http://67-72chevytrucks.com/vboard/s...d.php?t=654972 Past Restored Bench Seats:http://67-72chevytrucks.com/vboard/s...d.php?t=715398 PayPal link to pay for your items: https://www.paypal.me/TKCR

04-21-2021, 10:03 AM	#12
72c20customcamper Registered User Join Date: Jul 2018 Location: Catskill Mountains,NY Posts: 8,765	Re: Door alignment question I got them on Amazon but I also have a few box end wrenches I put a vise heated and bent them . __________________ Mark 72 c20 custom camper Husky edition, 66 SS396 Chevelle 1964 Hawk, 63 Avanti,62 lark 1969 AMX , 1968 c20 stepside ,85 K20 1977 Suburban sold 68 anniversary.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.