Wider Tire - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Jonboy · 07-08-2004, 11:45 PM

I have been thinking about 285/70's on a 10" wheel. I want a little rake after I lower it, and the tire should fill up those huge wheelwells.

86 Red_Bowtie · 07-09-2004, 12:03 AM

loblazer send me your pics again for some reason they didn't work when you sent them to me.

loblazer · 07-12-2004, 12:27 PM

OK 86 Red will do. Thanks

86 Red_Bowtie · 07-12-2004, 02:16 PM

These are pictures of loblazer Blazer.

86 Red_Bowtie · 07-12-2004, 02:17 PM

More of loblazer

86 Red_Bowtie · 07-12-2004, 02:18 PM

no problem.

apstguy · 07-12-2004, 02:53 PM

That blazer is sweet!

loweredd · 07-12-2004, 06:31 PM

Where is your back-up lights??

Coma · 07-12-2004, 09:49 PM

275/60's on the rear, 215/70's on the front lowered 4/6.

loblazer · 07-13-2004, 12:55 PM

Hi folks, 86 Red Bowtie was kind enough to put my pics up in 73 Blazer site. Thanks go out to him.

Running 2556015 Dunlops on front and 2756015 on rear, all on 8" burb rallies. I have 3- 1/2" wide Corvette trim rings. You can see the vette rings hide more wheel. I didn't have the knock offs on here as I gave the centres and k/o to my daughters boyfriend for his 67 C10. I have my NOS centres on and last night I put all new nuts on to replace rusty ones. Tomorrow night I will put on my new knock offs after I pick them up at auto store. They came last week but they were the wrong ones.

The taillights were made by me. The gas door is a 1996 Lumina van. Real easy swap to hide round gas holes.

Any other questions, let me know?

Doug

loblazer · 07-13-2004, 01:00 PM

Thanks Tyler

Loweredd - Back up lights are halogens on license frame. Were front driving lights but I had a better use.

She is lowered 5 and 5 with coils, spindles, c notch and flip kit. Belltech shocks all around.

Doug

DCRANER · 07-13-2004, 01:30 PM

I have 275 / 60 / 15's on 15 x 8 Weld wheels at all four corners, and a set of 325 / 50 / 15 Drag Radials on 15 x 10 Weld wheels so all matches. Run the Drag Radials until the snow hits, and they are not too big for the truck.

Doug

loweredd · 07-13-2004, 02:36 PM

Where did you get the taillights? I've never seen them without the backup lights in the lenses. Maybe it's a Canada thing.

Jonboy · 07-13-2004, 05:27 PM

Doug, what is the backspacing on your 15x10 wheels?

loblazer · 07-14-2004, 01:15 PM

TO LOWEREDD.....I made the lights myself. I bought 4 lenses with trim. I cut the top third off one and the bottom third off the other. I glued them together and covered the joint with an extra piece of trim. I did 1/3 and 2/3 as the housing has the same portions to house the tailight and backup. I then made both bulbs work as tail and stop. I bought a stainless license frame with halogen driving lights and put it on the back for back ups (BRIGHT).

TO JONBOY......

loblazer · 07-14-2004, 01:18 PM

TO JONBOY.......I am not running 10" I am running stock 8" rallies off a 1987 2wd suburban.

Doug

Jonboy · 07-14-2004, 02:04 PM

Oops, wrong Doug. DCRANER has the 10'S.

DCRANER · 07-14-2004, 02:30 PM

Quote:

Originally Posted by Jonboy

Oops, wrong Doug. DCRANER has the 10'S.

O/K, here I am. I will have to check when I go home tonight. But the wheels / tires fit very well with my truck lowered about 3".

Doug

rays68 · 07-18-2004, 01:37 AM

what year are the mirrors form

milner · 07-18-2004, 08:53 AM

Here is a pic of my 295/50-15 on a factory rally widened to 10".

**N2TRUX** · 07-18-2004, 10:51 AM

loblazer, You have all of us droolin on your ride. We need to see more of it. How about interior and motor pics?????

Jonboy · 07-18-2004, 09:21 PM

Quote:

Originally Posted by N2TRUX

loblazer, You have all of us droolin on your ride. We need to see more of it. How about interior and motor pics?????

I second that!

loblazer · 08-03-2004, 12:46 PM

TO RAYS68 - The mirrors are from a surplus store up here. $15.00 a pair. Were black plastic and we ainted them to match.

TO N2TRUX AND JONBOY - Thanks. I had redone the dash and the pad in grey pad and added a new GM, NOS gauge package. I only have stock grey seats right now. Will be doing 4 buckets in ivory or light beige leather as soon as I can find four. Will do the rugs and dash pad over again in cocoa brown to compliment the ivory. Will do the doors panels and rear panels in a a blend of the two colours.

The engine is a stock 350 with some chrome stuff, not pretty yet. Project for this winter.

Let me know if you still want pics?

screwballl · 08-03-2004, 12:57 PM

i prefer the 31x10.50x15, they seem to fill up the wheel well a bit better but still have the slitly wider traction stance

07-08-2004, 11:45 PM	#26
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	I have been thinking about 285/70's on a 10" wheel. I want a little rake after I lower it, and the tire should fill up those huge wheelwells. __________________ 1974 Jimmy- 5.3/4L80e/NP241

07-12-2004, 02:16 PM	#29
86 Red_Bowtie Registered User Join Date: Nov 2003 Location: South Wichita,KS Posts: 698	Pictures of loblazer These are pictures of loblazer Blazer.

07-12-2004, 02:53 PM	#32
apstguy LED King Join Date: Jan 2003 Location: Sacramento, CA Posts: 2,087	That blazer is sweet! __________________ Tyler 1985 C10 305 w/ Bowtie OD TH700R4 3.42 LSD 202,000 miles 2006 Ford Focus ZX3 5-speed Stick 2016 Chevy Spark EV Gone: 2002.5 VW GTI 24v VR6 Gone: 2008 VW R32

07-13-2004, 12:55 PM	#35
loblazer Senior Member Join Date: Mar 2004 Location: Fergus, Ontario Posts: 481	wider tire Hi folks, 86 Red Bowtie was kind enough to put my pics up in 73 Blazer site. Thanks go out to him. Running 2556015 Dunlops on front and 2756015 on rear, all on 8" burb rallies. I have 3- 1/2" wide Corvette trim rings. You can see the vette rings hide more wheel. I didn't have the knock offs on here as I gave the centres and k/o to my daughters boyfriend for his 67 C10. I have my NOS centres on and last night I put all new nuts on to replace rusty ones. Tomorrow night I will put on my new knock offs after I pick them up at auto store. They came last week but they were the wrong ones. The taillights were made by me. The gas door is a 1996 Lumina van. Real easy swap to hide round gas holes. Any other questions, let me know? Doug

07-13-2004, 01:00 PM	#36
loblazer Senior Member Join Date: Mar 2004 Location: Fergus, Ontario Posts: 481	wider tire Thanks Tyler Loweredd - Back up lights are halogens on license frame. Were front driving lights but I had a better use. She is lowered 5 and 5 with coils, spindles, c notch and flip kit. Belltech shocks all around. Doug

07-09-2004, 12:03 AM	#27
86 Red_Bowtie Registered User Join Date: Nov 2003 Location: South Wichita,KS Posts: 698	loblazer send me your pics again for some reason they didn't work when you sent them to me.

07-12-2004, 12:27 PM	#28
loblazer Senior Member Join Date: Mar 2004 Location: Fergus, Ontario Posts: 481	OK 86 Red will do. Thanks

07-12-2004, 02:17 PM	#30
86 Red_Bowtie Registered User Join Date: Nov 2003 Location: South Wichita,KS Posts: 698	More of loblazer

07-12-2004, 02:18 PM	#31
86 Red_Bowtie Registered User Join Date: Nov 2003 Location: South Wichita,KS Posts: 698	no problem.

07-12-2004, 06:31 PM	#33
loweredd www.loweredd.com Join Date: Aug 2002 Location: Struble IA Posts: 808	Where is your back-up lights??

07-12-2004, 09:49 PM	#34
Coma Registered User Join Date: Jan 2003 Location: u.s. Posts: 82	275/60's on the rear, 215/70's on the front lowered 4/6.

07-13-2004, 01:30 PM	#37
DCRANER Registered User Join Date: Feb 2004 Location: Atlantic Highlands, N.J. Posts: 139	I have 275 / 60 / 15's on 15 x 8 Weld wheels at all four corners, and a set of 325 / 50 / 15 Drag Radials on 15 x 10 Weld wheels so all matches. Run the Drag Radials until the snow hits, and they are not too big for the truck. Doug __________________ 86 GMC SWB, DK. BLUE, ZZ430,TH400, 4.11'S, HEADMAN CERAMIC HEADERS, WELD BILLETS, BFG 275 / 60 / 15, 325 / 50 / 15 DRAG RADIALS, FIBERGLASS COWL HOOD, B&M SHIFTER. MSD, MARCH PULLEYS / ALT. / PWR. STEER PUMP, BECOOL RAD., BILLET GRILL & GRANT WHEEL.

07-13-2004, 02:36 PM	#38
loweredd www.loweredd.com Join Date: Aug 2002 Location: Struble IA Posts: 808	Where did you get the taillights? I've never seen them without the backup lights in the lenses. Maybe it's a Canada thing.

07-13-2004, 05:27 PM	#39
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	Doug, what is the backspacing on your 15x10 wheels? __________________ 1974 Jimmy- 5.3/4L80e/NP241

07-14-2004, 01:15 PM	#40
loblazer Senior Member Join Date: Mar 2004 Location: Fergus, Ontario Posts: 481	TO LOWEREDD.....I made the lights myself. I bought 4 lenses with trim. I cut the top third off one and the bottom third off the other. I glued them together and covered the joint with an extra piece of trim. I did 1/3 and 2/3 as the housing has the same portions to house the tailight and backup. I then made both bulbs work as tail and stop. I bought a stainless license frame with halogen driving lights and put it on the back for back ups (BRIGHT). TO JONBOY......



Register or Log In To remove these advertisements.

07-14-2004, 01:18 PM	#41
loblazer Senior Member Join Date: Mar 2004 Location: Fergus, Ontario Posts: 481	TO JONBOY.......I am not running 10" I am running stock 8" rallies off a 1987 2wd suburban. Doug

07-14-2004, 02:04 PM	#42
Jonboy Slots go on anything! Join Date: May 2003 Location: Richardson, TX Posts: 5,957	Oops, wrong Doug. DCRANER has the 10'S. __________________ 1974 Jimmy- 5.3/4L80e/NP241

07-18-2004, 01:37 AM	#44
rays68 Registered User Join Date: Dec 2002 Location: Redondo Beach CA Posts: 131	what year are the mirrors form

07-18-2004, 08:53 AM	#45
milner Registered User Join Date: Jun 2003 Location: Mandan,ND Posts: 268	Here is a pic of my 295/50-15 on a factory rally widened to 10". Attached Images

07-18-2004, 10:51 AM	#46
N2TRUX Happy to be here Join Date: Mar 2000 Location: Cypress, TX Posts: 39,021	loblazer, You have all of us droolin on your ride. We need to see more of it. How about interior and motor pics????? __________________ Follow me on Facebook and Instagram @N2trux.com Articles- "Jake" the 84 to 74 crewcab "Elwood" the77_Remix 85 GMC Sierra "Scarlett" "Refining Sierra"

08-03-2004, 12:46 PM	#48
loblazer Senior Member Join Date: Mar 2004 Location: Fergus, Ontario Posts: 481	TO RAYS68 - The mirrors are from a surplus store up here. $15.00 a pair. Were black plastic and we ainted them to match. TO N2TRUX AND JONBOY - Thanks. I had redone the dash and the pad in grey pad and added a new GM, NOS gauge package. I only have stock grey seats right now. Will be doing 4 buckets in ivory or light beige leather as soon as I can find four. Will do the rugs and dash pad over again in cocoa brown to compliment the ivory. Will do the doors panels and rear panels in a a blend of the two colours. The engine is a stock 350 with some chrome stuff, not pretty yet. Project for this winter. Let me know if you still want pics?

08-03-2004, 12:57 PM	#49
screwballl Tonawanda 454 Join Date: Mar 2004 Location: Liquid Sunshine State Posts: 2,754	i prefer the 31x10.50x15, they seem to fill up the wheel well a bit better but still have the slitly wider traction stance __________________ 91 Chevy Suburban Tonawanda 454 R2500 - SOLD!!! 04 Dodge Durango 5.7L Hemi 2WD, 24K miles (as of July 2011) In the past 30 years about 90% of Fords are still on the road, the other 10% made it home. -------------------

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Register or Log In To remove these advertisements.