Wanted!!! - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**AspecialZ** · 04-24-2005, 11:29 PM

I am looking for the floor from a 73-87 cab, from the firewall back to the "hump" where the seat sits..thanks

LILREDGMC · 04-25-2005, 12:46 AM

I have an 85 that might have a decent floor. I have not looked at it closely, will do that tomorrow. From exactly where to where do you want for your project, so that I don't miss your needs or overlook a problem area.

LILREDGMC

**AspecialZ** · 04-25-2005, 11:22 PM

What i need is actually the entire floor, but more specifically from the base of the fire wall back the back of the cab along the sides of the rockers, I just don't want to do a cab swap, but there are places that the rust has taken over, where in Pgh, pa are you, I work in sewickly?

muddyole 69 · 04-26-2005, 03:25 AM

Hey I have a pretty decent cab that if you want I can get pics of maybe we can work out a deal on the parts you got against the cab let me know either way see ya wednesday Mike

LILREDGMC · 04-26-2005, 10:31 AM

I live on the East side, Penn Hills, the cab is about 22 miles east in Saltsburg. I did not get to inspect it yet. The cab was wrecked, on the drivers side door so you would not want to attempt a cab swap. I'll post the results when I inspect. I'll try to get a pic or two.

LILREDGMC · 04-26-2005, 09:26 PM

Did not get there today, but was advised the cab was decent before it got hit in left front. The rockers and cab corners were in need of redo, but the floor and firewall had no issues. Hope to get a pic tomorrow so you can decide. Expect to do some clean up at the shop so numerous pieces will be prepared for the recycle routine. The price of scrap steel continues to rise.

LILREDGMC

LILREDGMC · 05-07-2005, 10:34 PM

We cut up the cab today. I told Rich if it was not rusted to save the floor. The cab floor had little to no rust, but ... it had been hit on the left side and the rocker and cab corner were pushed in toward the floor. The rolled up area under the seat on the drivers side has some damage, but Rich who is more experienced than I, says if the rocker was pulled, the pan damage will come out easily. They cut the floor high on the front kick panels, and left the cab corners and some rear panel intact.

I will download the pics to my pic site and then post here shortly.

LILREDGMC

LILREDGMC · 05-07-2005, 10:48 PM

Pics are from the right

Drivers side note the roll on the floor under the seat.

Pics from the front looking under at supports

Hopefully these will give you a fair picture. Let me know what your plans are or are not.

LILREDGMC · 05-09-2005, 11:31 PM

AZ

The scrap yard beckons. Need to know before the weekend your interest in the floor.

Thanks for a reply

LILREDGMC

**AspecialZ** · 05-10-2005, 12:40 AM

if you don't want alot for it, it may make patching a lot easier for me rather that using the entire floor, as my driver side is the worst side, where yours is wrecked, what do you want for it?

LILREDGMC · 05-10-2005, 08:29 AM

How's $20? I am out through Friday for a work assignment, we could arrange how to meet after that. You work near Sewickly, I could try to meet you or drop it off next week. Or you could consider next weekend. The floor is still at the shop, I will bring it to the house after my trip. Let me know your thoughts and plans. I may be a little slow on email until Friday.

LILREDGMC

04-24-2005, 11:29 PM	#1
AspecialZ Street Rod Restoration Join Date: Jan 2004 Location: Wellsburg, WV Posts: 882	Wanted!!! I am looking for the floor from a 73-87 cab, from the firewall back to the "hump" where the seat sits..thanks __________________ Follow me on Instagram @ hot_rod_shop

04-25-2005, 12:46 AM	#2
LILREDGMC Registered User Join Date: Oct 2001 Location: Pittsburgh, Pennsylvania USA Posts: 461	Cab Floor I have an 85 that might have a decent floor. I have not looked at it closely, will do that tomorrow. From exactly where to where do you want for your project, so that I don't miss your needs or overlook a problem area. LILREDGMC

04-25-2005, 11:22 PM	#3
AspecialZ Street Rod Restoration Join Date: Jan 2004 Location: Wellsburg, WV Posts: 882	... What i need is actually the entire floor, but more specifically from the base of the fire wall back the back of the cab along the sides of the rockers, I just don't want to do a cab swap, but there are places that the rust has taken over, where in Pgh, pa are you, I work in sewickly? __________________ Follow me on Instagram @ hot_rod_shop

04-26-2005, 03:25 AM	#4
muddyole 69 Senior Member Join Date: Jan 2004 Location: SE Ohio Posts: 1,121	Parts Hey I have a pretty decent cab that if you want I can get pics of maybe we can work out a deal on the parts you got against the cab let me know either way see ya wednesday Mike __________________ hav'n fun be'n me

04-26-2005, 10:31 AM	#5
LILREDGMC Registered User Join Date: Oct 2001 Location: Pittsburgh, Pennsylvania USA Posts: 461	Cab Floor I live on the East side, Penn Hills, the cab is about 22 miles east in Saltsburg. I did not get to inspect it yet. The cab was wrecked, on the drivers side door so you would not want to attempt a cab swap. I'll post the results when I inspect. I'll try to get a pic or two.

04-26-2005, 09:26 PM	#6
LILREDGMC Registered User Join Date: Oct 2001 Location: Pittsburgh, Pennsylvania USA Posts: 461	Cab Floor Did not get there today, but was advised the cab was decent before it got hit in left front. The rockers and cab corners were in need of redo, but the floor and firewall had no issues. Hope to get a pic tomorrow so you can decide. Expect to do some clean up at the shop so numerous pieces will be prepared for the recycle routine. The price of scrap steel continues to rise. LILREDGMC

05-07-2005, 10:34 PM	#7
LILREDGMC Registered User Join Date: Oct 2001 Location: Pittsburgh, Pennsylvania USA Posts: 461	Floor - pics on the way We cut up the cab today. I told Rich if it was not rusted to save the floor. The cab floor had little to no rust, but ... it had been hit on the left side and the rocker and cab corner were pushed in toward the floor. The rolled up area under the seat on the drivers side has some damage, but Rich who is more experienced than I, says if the rocker was pulled, the pan damage will come out easily. They cut the floor high on the front kick panels, and left the cab corners and some rear panel intact. I will download the pics to my pic site and then post here shortly. LILREDGMC

05-07-2005, 10:48 PM	#8
LILREDGMC Registered User Join Date: Oct 2001 Location: Pittsburgh, Pennsylvania USA Posts: 461	1985 Cab Floor Pics are from the right Drivers side note the roll on the floor under the seat. Pics from the front looking under at supports Hopefully these will give you a fair picture. Let me know what your plans are or are not.

05-09-2005, 11:31 PM	#9
LILREDGMC Registered User Join Date: Oct 2001 Location: Pittsburgh, Pennsylvania USA Posts: 461	Cab Floor AZ The scrap yard beckons. Need to know before the weekend your interest in the floor. Thanks for a reply LILREDGMC

05-10-2005, 12:40 AM	#10
AspecialZ Street Rod Restoration Join Date: Jan 2004 Location: Wellsburg, WV Posts: 882	... if you don't want alot for it, it may make patching a lot easier for me rather that using the entire floor, as my driver side is the worst side, where yours is wrecked, what do you want for it? __________________ Follow me on Instagram @ hot_rod_shop

05-10-2005, 08:29 AM	#11
LILREDGMC Registered User Join Date: Oct 2001 Location: Pittsburgh, Pennsylvania USA Posts: 461	Floor How's $20? I am out through Friday for a work assignment, we could arrange how to meet after that. You work near Sewickly, I could try to meet you or drop it off next week. Or you could consider next weekend. The floor is still at the shop, I will bring it to the house after my trip. Let me know your thoughts and plans. I may be a little slow on email until Friday. LILREDGMC



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.