New floors thread.. - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

FRENCHBLUE72 · 05-23-2006, 10:49 PM

So far I have used an air powered cut off wheel and a hammer and chesiel.. I will post pics untill I am done..

vtblazer · 05-24-2006, 05:57 AM

Quote:

Originally Posted by FRENCHBLUE72

Do blazers have the inner backing plate like a truck does?? Or is that what is included on the floor patch pannel?? Kurt you planning a vacation to oregon anytime soon?????

Yes, they have the inner panel also.
Make sure you retain the bolts for the rockers, both inner and outer/front and back.

Any cheap air fairs going on right now?

Having fun yet...

mtnbutch · 05-24-2006, 08:53 PM

Really Glad you are showing detailed pictures as I am about to tackle my rockers and the small corners of the floor.......

FRENCHBLUE72 · 05-24-2006, 11:36 PM

I did not get too much done today it was more of a cut fit cut fit cut fit followed but weld cool weld cool weld cool I seem to be getting it...

FRENCHBLUE72 · 05-24-2006, 11:40 PM

Looks like I am gonna have to stretch the replacement pannel up around the curved section of floor.. Also found out the rockers have been replaced at one point check out the bogger job... The rockers are solid so I am gonna see if I can save the rocker pannel but make em fit nicer like the floor.. Kurt I dont know about air fairs maybe you should just drive the blazer so we can go wheeling while your here helping out..

**raggedjim** · 05-25-2006, 12:50 PM

French, good work! The only drawback to not replacing the rocker panels is you will not be 100% sure of the condition of the lower a pillar (front) and b pillar (rear). Given the work you've done so far it would be a shame not to replace those IF they need it. Here's an idea of how bad they can be, even when the outer rocker looks solid... And an after shoot, if I can do this anyone can!

Good luck, Rg

FRENCHBLUE72 · 05-25-2006, 07:07 PM

Ya roger I have been thinking about just pulling the rockers offand if everything is good then I ll just weld them back on.. Gotta go get to work need this done soon..

trucky72 · 05-29-2006, 01:07 PM

I don't have a problem of a confused p/o, sadly, I think I'm going to end up wearing that nametag... Good luck! Rock on!

OLD DAWG · 06-02-2006, 02:07 PM

Quote:

Originally Posted by vtblazer

Done by Monday huh?

Why is it that the P/O's never seem to get it right?

I actually found a couple of soup cans used in areas for body panel support. placed by P/O

**raggedjim** · 06-02-2006, 02:18 PM

Heck, if it weren't for soup cans and old license plates my first blazer would have fell apart!

Welcome to the board Old dawg, Rg

krue · 06-02-2006, 03:06 PM

Hey Old Dawg, post a thread on the Welcome board so everyone can say hey.

FRENCHBLUE72 · 06-05-2006, 10:37 PM

Just an update the floors should be back in friday with pics been having lots of family health problems and family is always 1st...

FRENCHBLUE72 · 07-04-2006, 12:02 PM

The passenger side is done I had some bad luck and ran out of gas and batterys in the camera this was the last shot I got before the batterys died..

Chevyman63 · 07-04-2006, 03:08 PM

When will you be starting the driver's side? Can't wait to see more pics. Great job!

FRENCHBLUE72 · 07-04-2006, 04:05 PM

More than likley this winter cause I pulled the top off today....

05-23-2006, 10:49 PM	#26
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: New floors thread.. So far I have used an air powered cut off wheel and a hammer and chesiel.. I will post pics untill I am done.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

05-24-2006, 08:53 PM	#28
mtnbutch Registered User Join Date: Apr 2001 Location: Richmond,Ks USA Posts: 24	Re: New floors thread.. Really Glad you are showing detailed pictures as I am about to tackle my rockers and the small corners of the floor.......

05-24-2006, 11:36 PM	#29
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: New floors thread.. I did not get too much done today it was more of a cut fit cut fit cut fit followed but weld cool weld cool weld cool I seem to be getting it... Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

05-24-2006, 11:40 PM	#30
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: New floors thread.. Looks like I am gonna have to stretch the replacement pannel up around the curved section of floor.. Also found out the rockers have been replaced at one point check out the bogger job... The rockers are solid so I am gonna see if I can save the rocker pannel but make em fit nicer like the floor.. Kurt I dont know about air fairs maybe you should just drive the blazer so we can go wheeling while your here helping out.. Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

05-25-2006, 12:50 PM	#31
raggedjim Senior Member Join Date: Jun 2002 Location: Murray, Kentucky Posts: 3,484	Re: New floors thread.. French, good work! The only drawback to not replacing the rocker panels is you will not be 100% sure of the condition of the lower a pillar (front) and b pillar (rear). Given the work you've done so far it would be a shame not to replace those IF they need it. Here's an idea of how bad they can be, even when the outer rocker looks solid... And an after shoot, if I can do this anyone can! Good luck, Rg Attached Images __________________ Roger '68 Short step - https://67-72chevytrucks.com/vboard/...d.php?t=849675 '69 ('70?) 2wd Blazer '70 GMC Jimmy 2wd '73 Firebird - https://67-72chevytrucks.com/vboard/...d.php?t=853203 Ideas - https://67-72chevytrucks.com/vboard/...d.php?t=851743 Last edited by raggedjim; 05-25-2006 at 12:51 PM.

05-25-2006, 07:07 PM	#32
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: New floors thread.. Ya roger I have been thinking about just pulling the rockers offand if everything is good then I ll just weld them back on.. Gotta go get to work need this done soon.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

05-29-2006, 01:07 PM	#33
trucky72 Registered User Join Date: May 2006 Location: virginia beach, virginia Posts: 16	Re: New floors thread.. I don't have a problem of a confused p/o, sadly, I think I'm going to end up wearing that nametag... Good luck! Rock on!

06-02-2006, 02:18 PM	#35
raggedjim Senior Member Join Date: Jun 2002 Location: Murray, Kentucky Posts: 3,484	Re: New floors thread.. Heck, if it weren't for soup cans and old license plates my first blazer would have fell apart! Welcome to the board Old dawg, Rg __________________ Roger '68 Short step - https://67-72chevytrucks.com/vboard/...d.php?t=849675 '69 ('70?) 2wd Blazer '70 GMC Jimmy 2wd '73 Firebird - https://67-72chevytrucks.com/vboard/...d.php?t=853203 Ideas - https://67-72chevytrucks.com/vboard/...d.php?t=851743

06-02-2006, 03:06 PM	#36
krue Designated A-hole! Join Date: Mar 2003 Location: South Mississippi Posts: 36,448	Re: New floors thread.. Hey Old Dawg, post a thread on the Welcome board so everyone can say hey. __________________ "If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck"

06-05-2006, 10:37 PM	#37
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: New floors thread.. Just an update the floors should be back in friday with pics been having lots of family health problems and family is always 1st... __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

07-04-2006, 12:02 PM	#38
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: New floors thread.. The passenger side is done I had some bad luck and ran out of gas and batterys in the camera this was the last shot I got before the batterys died.. Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

07-04-2006, 03:08 PM	#39
Chevyman63 Can't wait to retire!! Join Date: Feb 2003 Location: Corunna, MI Posts: 1,575	Re: New floors thread.. When will you be starting the driver's side? Can't wait to see more pics. Great job!

07-04-2006, 04:05 PM	#40
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,606	Re: New floors thread.. More than likley this winter cause I pulled the top off today.... __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.