Wiring help? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

ChevyDude · 06-03-2006, 01:56 PM

I really am having lots of quetions as I am diving into this thing. In advance I will thank everyone for their help, it is appreciated!

So I need an answer here. I just took this pic then I found a pic showing where they go accept for that pink and yellow...I am assuming they go to the HEI IGN. cap??? Any help would be great. I don't think I have anything for that that blue wire (oil pressure) to plug into, I have a mechanical oil gauge. My wiring harness is from M & H and supposed to be like the original but adapted to HEI setup. I really don't know where all the cadium bracket bolt down to. And it seems the silonode wire cirlce ends are too small???

krue · 06-03-2006, 03:05 PM

You shouldn't need the yellow wire from the solenoid to the dizzy w/HEI. The pink wire should be all you need (may want to measure the resistance to make sure it's not a points style resistance wire). My truck has a mechanical oil pressure gage, but the engine (original) has the oil pressure sending unit on the pass side rear of the head.

ChevyDude · 06-03-2006, 03:37 PM

Thank YOU!!! I'm going to get all the mechanical stuff together and if I can't get all the wiring I'll get one of my mechanic friends from John Elway Chevrolet to come do the final wiring. That yellow and pink wire that has a white clip on it fits perfectly on the HEI cap??? I'm not going to worry too much. On the the tie rods, sway bar, next!

06-03-2006, 01:56 PM	#1
ChevyDude Senior Member Join Date: Jun 2003 Location: Westminster, CO Posts: 3,071	Wiring help? I really am having lots of quetions as I am diving into this thing. In advance I will thank everyone for their help, it is appreciated! So I need an answer here. I just took this pic then I found a pic showing where they go accept for that pink and yellow...I am assuming they go to the HEI IGN. cap??? Any help would be great. I don't think I have anything for that that blue wire (oil pressure) to plug into, I have a mechanical oil gauge. My wiring harness is from M & H and supposed to be like the original but adapted to HEI setup. I really don't know where all the cadium bracket bolt down to. And it seems the silonode wire cirlce ends are too small??? Attached Images Last edited by ChevyDude; 06-03-2006 at 01:58 PM.

06-03-2006, 03:05 PM	#2
krue Designated A-hole! Join Date: Mar 2003 Location: South Mississippi Posts: 36,448	Re: Wiring help? You shouldn't need the yellow wire from the solenoid to the dizzy w/HEI. The pink wire should be all you need (may want to measure the resistance to make sure it's not a points style resistance wire). My truck has a mechanical oil pressure gage, but the engine (original) has the oil pressure sending unit on the pass side rear of the head. __________________ "If it ain't broke, fix it 'til it is!" Being stupid ain't illegal. We're Still Debt Free Except for the House!!! www.daveramsey.com 70 GMC SWB Stepside project "Green Booger" soon to be 6.0l/4l80e 93 S-10 "Poppaw's Truck"

06-03-2006, 03:37 PM	#3
ChevyDude Senior Member Join Date: Jun 2003 Location: Westminster, CO Posts: 3,071	Re: Wiring help? Thank YOU!!! I'm going to get all the mechanical stuff together and if I can't get all the wiring I'll get one of my mechanic friends from John Elway Chevrolet to come do the final wiring. That yellow and pink wire that has a white clip on it fits perfectly on the HEI cap??? I'm not going to worry too much. On the the tie rods, sway bar, next!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.