Custom Chassis with canti setup - Page 14 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

SCOTI · 01-15-2007, 02:47 PM

Valleycustom,
Porter mentioned you had gotten a Dropmember from him & it was to be installed in a truck that had a big block. Have you made any progress on this particular project? I was curious about the R&P vs. the balancer & headers.

ELTC · 01-15-2007, 05:20 PM

im new to the board and i would have to agree with everyone else your work is almost god like, my girl had to help me pick my jaw up,

valleycustom · 01-15-2007, 07:41 PM

Quote:

Originally Posted by SCOTI

Valleycustom,
Porter mentioned you had gotten a Dropmember from him & it was to be installed in a truck that had a big block. Have you made any progress on this particular project? I was curious about the R&P vs. the balancer & headers.

Yeah I got a C4 dropmember. I'm not sure about the balancer issue. When I mocked up the motor it didn't have one on, but I can check. As far as the headers I'm building them myself. I will get some pics posted on the other thread I have going for that truck sometime this week.

Later
Jr

hammered · 03-15-2007, 02:23 PM

Quote:

Originally Posted by DroppedZ84

Good deal, really.
Yeah, I take that back about Killer Ridez, I drove by there today, and the shop was being loaded with some other company..so yeah, I guess they ARE defunct.

Let me clarify.... Killer Ridez, Inc. is open in Seagoville, TX... You may be talking about Killer Customs

Check Out www.killerridez.com

*Shane* · 03-15-2007, 05:39 PM

nice shameless plug ...

XXL · 03-15-2007, 06:46 PM

Quote:

Originally Posted by Shane

nice shameless plug ...

He earned it... look at that post count!

*Shane* · 03-15-2007, 08:04 PM

my bad ... you're right ... my apologies

hotrods316 · 08-02-2007, 10:21 PM

any updates JR?
Sick work I love going back and looking at it all.

valleycustom · 08-03-2007, 03:03 PM

Quote:

Originally Posted by hotrods316

any updates JR?
Sick work I love going back and looking at it all.

Dang this thread is dusty!!! Yeah the frame is finished. I'll take some pics. Its just sitting at the shop right now getting dusty. I'm going to get the bed mounted here in the next couple of weeks and im going to bomb it black and lay down some pin stripes. I still have to send the chassis out to powder coat. I'm working on another chassis right now that's all C4. I'll have to get a thread going on that one also.

cornutz · 08-03-2007, 06:30 PM

Yeah this thread is dusty...Lets see some pics Queen Jr...

valleycustom · 08-03-2007, 06:34 PM

Quote:

Originally Posted by cornutz

Yeah this thread is dusty...Lets see some pics Queen Jr...

Here you go bill.

valleycustom · 11-29-2007, 11:21 PM

Here's a pic of the truck as of Sunday.

valleycustom · 11-30-2007, 12:20 AM

Another

valleycustom · 11-30-2007, 12:22 AM

..

PRUNEDA · 11-30-2007, 01:00 AM

Man, thats going to be sweet when done. The Intro wheels look good too.

Super73 · 12-01-2007, 01:48 PM

Quote:

I also changed over the C10 spindles to work with the mustang ball joints so I can run 6 lug.

Did you have to reem the C10 spindle to fit the Mustan ball joint?

If the mustang Ball joint is smaller in diameter, what did you do to the C10 spindle to make it work??

Reason I am asking is I was thinking of doing a similar thing with mine to reduce some weight in the front. Mine is a drag racing application. I figure since you already made it work, your advise would save me both time and money I am sure.. Thanks in advance.

Shaun

valleycustom · 12-01-2007, 06:00 PM

I reamed the upper to fit the MII. The bottom was a little more involved. I made a bung that had the correct tapper for the lower balljoint then I machined the lower bj hole so I can press the bung in and weld it in place.

Super73 · 12-01-2007, 06:46 PM

So you welded the bung to the cast spidle or to the ball joing shaft?

I'm assuming you tiged the bung, did you preheat the spindle and cool it in an oven to keep the weld from craking (if it was welded to the cast spindle?

valleycustom · 12-01-2007, 09:33 PM

Quote:

Originally Posted by Super73

So you welded the bung to the cast spidle or to the ball joing shaft?

I'm assuming you tiged the bung, did you preheat the spindle and cool it in an oven to keep the weld from craking (if it was welded to the cast spindle?

Yes I preheated the spindle before I TIG welded it. Also dont cut the hole all the way through the spindle so the bung will bottom out when you press it in. If you know how to weld cast you should be fine. I'll take some pics so you can see.

Later
Jr

Super73 · 12-02-2007, 01:34 AM

Thanks JR.. I haven't tiged nor welded cast (properley). Bolted a vise down and welded it to a bench when I first started laying nice mig beads. But it cracked

Have any interest in doing another set of spindles?

Kontrol Phreaks · 12-05-2007, 11:37 AM

New location from the last one I visited as well. Guess I'm going to have to get directions to the new place before I head over to peep the project. Maybe I'll bring my C10 over there and we can have a projectfest and get some work done on both.

Clint

valleycustom · 12-05-2007, 12:45 PM

Quote:

Originally Posted by Kontrol Phreaks

New location from the last one I visited as well. Guess I'm going to have to get directions to the new place before I head over to peep the project. Maybe I'll bring my C10 over there and we can have a projectfest and get some work done on both.

Clint

Yeah I'm out in Waterhole now. Real easy to find. Hit me up!

Sweet 85 C10 · 12-12-2007, 04:13 PM

WOW! This project is tight man! That frame is strong man! Good JOB!!! Nice to see people take pride in there work.

valleycustom · 01-05-2008, 12:33 PM

Here are some pics of the truck at RESO last week.

Slmd92DIME · 01-05-2008, 01:31 PM

Great work and that is one sick truck

01-15-2007, 02:47 PM	#326
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 22,068	Re: Custom Chassis with canti setup Valleycustom, Porter mentioned you had gotten a Dropmember from him & it was to be installed in a truck that had a big block. Have you made any progress on this particular project? I was curious about the R&P vs. the balancer & headers. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.* Last edited by SCOTI; 01-15-2007 at 02:48 PM.

01-15-2007, 05:20 PM	#327
ELTC Registered User Join Date: Dec 2006 Location: New York Posts: 3	Re: Custom Chassis with canti setup im new to the board and i would have to agree with everyone else your work is almost god like, my girl had to help me pick my jaw up,

03-15-2007, 05:39 PM	#330
Shane Account Suspended Join Date: Jun 2000 Location: over yonder Posts: 14,270	Re: Custom Chassis with canti setup nice shameless plug ...

03-15-2007, 08:04 PM	#332
Shane Account Suspended Join Date: Jun 2000 Location: over yonder Posts: 14,270	Re: Custom Chassis with canti setup my bad ... you're right ... my apologies

08-02-2007, 10:21 PM	#333
hotrods316 Registered User Join Date: Jun 2006 Location: d-town Posts: 11	Re: Custom Chassis with canti setup any updates JR? Sick work I love going back and looking at it all.

08-03-2007, 06:30 PM	#335
cornutz All Praise RANDY!! Join Date: Sep 2004 Location: Central California Posts: 391	Re: Custom Chassis with canti setup Yeah this thread is dusty...Lets see some pics Queen Jr...

11-29-2007, 11:21 PM	#337
valleycustom Registered User Join Date: Mar 2005 Location: Modesto, Ca Posts: 225	Re: Custom Chassis with canti setup Here's a pic of the truck as of Sunday. Attached Images __________________ Please become a site supporting vendor to advertise a business in your signature. you can do so here

11-30-2007, 12:20 AM	#338
valleycustom Registered User Join Date: Mar 2005 Location: Modesto, Ca Posts: 225	Re: Custom Chassis with canti setup Another Attached Images __________________ Please become a site supporting vendor to advertise a business in your signature. you can do so here

11-30-2007, 12:22 AM	#339
valleycustom Registered User Join Date: Mar 2005 Location: Modesto, Ca Posts: 225	Re: Custom Chassis with canti setup .. Attached Images __________________ Please become a site supporting vendor to advertise a business in your signature. you can do so here

11-30-2007, 01:00 AM	#340
PRUNEDA '87 Join Date: Jun 2004 Location: Katy, TX Posts: 632	Re: Custom Chassis with canti setup Man, thats going to be sweet when done. The Intro wheels look good too.

12-01-2007, 06:00 PM	#342
valleycustom Registered User Join Date: Mar 2005 Location: Modesto, Ca Posts: 225	Re: Custom Chassis with canti setup I reamed the upper to fit the MII. The bottom was a little more involved. I made a bung that had the correct tapper for the lower balljoint then I machined the lower bj hole so I can press the bung in and weld it in place. __________________ Please become a site supporting vendor to advertise a business in your signature. you can do so here

12-01-2007, 06:46 PM	#343
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: Custom Chassis with canti setup So you welded the bung to the cast spidle or to the ball joing shaft? I'm assuming you tiged the bung, did you preheat the spindle and cool it in an oven to keep the weld from craking (if it was welded to the cast spindle?

12-02-2007, 01:34 AM	#345
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: Custom Chassis with canti setup Thanks JR.. I haven't tiged nor welded cast (properley). Bolted a vise down and welded it to a bench when I first started laying nice mig beads. But it cracked Have any interest in doing another set of spindles?

12-05-2007, 11:37 AM	#346
Kontrol Phreaks Registered User Join Date: Feb 2006 Location: Central Cali Posts: 242	Re: Custom Chassis with canti setup New location from the last one I visited as well. Guess I'm going to have to get directions to the new place before I head over to peep the project. Maybe I'll bring my C10 over there and we can have a projectfest and get some work done on both. Clint __________________ - Clint -

12-12-2007, 04:13 PM	#348
Sweet 85 C10 OG Join Date: Sep 2007 Location: Orlando Florida Posts: 146	Re: Custom Chassis with canti setup WOW! This project is tight man! That frame is strong man! Good JOB!!! Nice to see people take pride in there work.



Register or Log In To remove these advertisements.

01-05-2008, 12:33 PM	#349
valleycustom Registered User Join Date: Mar 2005 Location: Modesto, Ca Posts: 225	Re: Custom Chassis with canti setup Here are some pics of the truck at RESO last week. Attached Images __________________ Please become a site supporting vendor to advertise a business in your signature. you can do so here

01-05-2008, 01:31 PM	#350
Slmd92DIME Registered User Join Date: Mar 2007 Location: West Virginia Posts: 481	Re: Custom Chassis with canti setup Great work and that is one sick truck

Register or Log In To remove these advertisements.