81-87 4x4 u-bolts & plates for corp 10 axle - The 1947 - Present Chevrolet & GMC Truck Message Board Network

62 short step · 08-11-2007, 08:32 PM

Looking for a complete set. Putting a corp 10 axle under my 61 4x4 and I need these soon as possible. Thanks, Jeremy.

**jerry moss** · 08-12-2007, 01:32 PM

what is the diameter of your 10 bolt axle tubes- 2 3/4" or 3". if it's 2 3/4" your old plates and u-bolts should work.i have several sets of plates but all are for 2 3/4" tubes.

62 short step · 08-12-2007, 03:45 PM

Thanks Jerry, but its a 3" tube.

**jerry moss** · 08-12-2007, 11:49 PM

Jeremy,
i just found another set of u-bolt plates i had forgotten about, they're of a mid 80s 3/4 ton suburban that had a 10 bolt front diff. with 3 inch tubes. the only u-bolts i have are for a stock front suspension and will not be long enough for your application. you can get u-bolts in almost any configuration from your local NAPA parts store. the plates will fit in a flat rate box so if you want them, i'll sell them for $30.00 delivered.

LILREDGMC · 08-13-2007, 06:48 AM

Jerry

Thanks for the heads up on axle tube diameter. I have some plates, some from 3/4, and the set from the 89 Suburban , but most of my U bolts suffer from the corrosion issues. Appreciate the info to prevent a whooooops.

LILREDGMC

62 short step · 08-13-2007, 11:21 PM

Found some. Thanks Jerry!

62 short step · 08-15-2007, 11:01 AM

Money order is in the mail as of today! Thanks again Jerry. Jeremy.

**jerry moss** · 08-15-2007, 08:52 PM

plates should be there by friday.

62 short step · 08-15-2007, 10:46 PM

Sounds good! Thanks!!

08-11-2007, 08:32 PM	#1
62 short step Senior Member Join Date: Aug 2005 Location: Greenwell Springs, Louisiana Posts: 2,882	Want to buy 81-87 4x4 u-bolts & plates for corp 10 axle Looking for a complete set. Putting a corp 10 axle under my 61 4x4 and I need these soon as possible. Thanks, Jeremy. Last edited by 62 short step; 08-11-2007 at 08:38 PM.

08-12-2007, 01:32 PM	#2
jerry moss Born Psycho Join Date: Feb 2001 Location: brentwood,cal,usa Posts: 4,941	Re: 81-87 4x4 u-bolts & plates for corp 10 axle what is the diameter of your 10 bolt axle tubes- 2 3/4" or 3". if it's 2 3/4" your old plates and u-bolts should work.i have several sets of plates but all are for 2 3/4" tubes. __________________ jerry moss 72 cheyenne super K20- tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,tow hooks,bumper guards,toolbox,aux. fuel tank,posi front and rear,plus other goodies!!! SOLD 69 suburban K20-tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,4 inch all spring lift,4 speed, 14 bolt full floater, dana 44 HD,warn winch,posi front and rear,tow hooks,plus other goodies. 73/80 chevy/gmc K20 SB400,turbo 400,205,tilt,a-c,gas hog. 77 K/5 cheyenne blazer-daily driver/beater. SON HAS IT NOW BRENTWOOD,CALIFORNIA

08-12-2007, 03:45 PM	#3
62 short step Senior Member Join Date: Aug 2005 Location: Greenwell Springs, Louisiana Posts: 2,882	Re: 81-87 4x4 u-bolts & plates for corp 10 axle Thanks Jerry, but its a 3" tube.

08-12-2007, 11:49 PM	#4
jerry moss Born Psycho Join Date: Feb 2001 Location: brentwood,cal,usa Posts: 4,941	Re: 81-87 4x4 u-bolts & plates for corp 10 axle Jeremy, i just found another set of u-bolt plates i had forgotten about, they're of a mid 80s 3/4 ton suburban that had a 10 bolt front diff. with 3 inch tubes. the only u-bolts i have are for a stock front suspension and will not be long enough for your application. you can get u-bolts in almost any configuration from your local NAPA parts store. the plates will fit in a flat rate box so if you want them, i'll sell them for $30.00 delivered. __________________ jerry moss 72 cheyenne super K20- tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,tow hooks,bumper guards,toolbox,aux. fuel tank,posi front and rear,plus other goodies!!! SOLD 69 suburban K20-tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,4 inch all spring lift,4 speed, 14 bolt full floater, dana 44 HD,warn winch,posi front and rear,tow hooks,plus other goodies. 73/80 chevy/gmc K20 SB400,turbo 400,205,tilt,a-c,gas hog. 77 K/5 cheyenne blazer-daily driver/beater. SON HAS IT NOW BRENTWOOD,CALIFORNIA

08-13-2007, 06:48 AM	#5
LILREDGMC Registered User Join Date: Oct 2001 Location: Pittsburgh, Pennsylvania USA Posts: 461	Re: 81-87 4x4 u-bolts & plates for corp 10 axle Jerry Thanks for the heads up on axle tube diameter. I have some plates, some from 3/4, and the set from the 89 Suburban , but most of my U bolts suffer from the corrosion issues. Appreciate the info to prevent a whooooops. LILREDGMC

08-13-2007, 11:21 PM	#6
62 short step Senior Member Join Date: Aug 2005 Location: Greenwell Springs, Louisiana Posts: 2,882	Re: 81-87 4x4 u-bolts & plates for corp 10 axle Found some. Thanks Jerry!

08-15-2007, 11:01 AM	#7
62 short step Senior Member Join Date: Aug 2005 Location: Greenwell Springs, Louisiana Posts: 2,882	Re: 81-87 4x4 u-bolts & plates for corp 10 axle Money order is in the mail as of today! Thanks again Jerry. Jeremy.

08-15-2007, 08:52 PM	#8
jerry moss Born Psycho Join Date: Feb 2001 Location: brentwood,cal,usa Posts: 4,941	Re: 81-87 4x4 u-bolts & plates for corp 10 axle plates should be there by friday. __________________ jerry moss 72 cheyenne super K20- tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,tow hooks,bumper guards,toolbox,aux. fuel tank,posi front and rear,plus other goodies!!! SOLD 69 suburban K20-tilt,tach,vacuum,speedwarning,buckets,shoulder belts,am/fm,4 inch all spring lift,4 speed, 14 bolt full floater, dana 44 HD,warn winch,posi front and rear,tow hooks,plus other goodies. 73/80 chevy/gmc K20 SB400,turbo 400,205,tilt,a-c,gas hog. 77 K/5 cheyenne blazer-daily driver/beater. SON HAS IT NOW BRENTWOOD,CALIFORNIA

08-15-2007, 10:46 PM	#9
62 short step Senior Member Join Date: Aug 2005 Location: Greenwell Springs, Louisiana Posts: 2,882	Re: 81-87 4x4 u-bolts & plates for corp 10 axle Sounds good! Thanks!!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.