What do you think this ran - The 1947 - Present Chevrolet & GMC Truck Message Board Network

djracer · 02-09-2009, 02:24 PM

71 swb fleetside
Gm Goodwrench 350
Weiand Action plus
Speed demon 650 vacuum secondary
Comp cam xe262 .462/.469 262/270
hei distributor
5/8 hedders
2.25 exhaust
40 series flowmasters

Peg leg rear with unknown gear

275/60 radials all the way around.

Nothing removed from truck. I 'll give you guys a couple days of guessing before I post a times.

This was a 6cyl 3 speed truck what gear should it have?

joeys66pickup · 02-09-2009, 02:36 PM

im guessing with the sixer the gear was Alittle Lower then usual?.....

Im guessing a 12.9xx

PhilaTruck · 02-09-2009, 03:11 PM

I think the rear gear is key to guessing how this stock set-up would perform, but I'll guess 15, based on a highway gear.

71chevytruckguy · 02-09-2009, 03:54 PM

Im gonna say 9.8 @ 70 mph in the 1/8. Chris.

Super73 · 02-09-2009, 04:01 PM

Still the manual 3speed?

If auto, how big of a stall?

djracer · 02-09-2009, 04:28 PM

turbo 350 2000 stall

Super73 · 02-09-2009, 04:59 PM

60' --- 2.12
1/8 --- 8.82 @ 81.4
1/4 --- 13.76 @ 98.7

Marv D · 02-09-2009, 05:14 PM

pretty tough with the limited info there Kevin,, but I'll bite

14.2's at around 85-90ish mph,,, guessing it had 3.73 gears from the era which seems was common with manuals and straight 6's,, but if it was one of the hwy gear trucks (3.0x gears,,, closer to 14.9's or more would be my guess.

Wild83C10 · 02-09-2009, 06:04 PM

Well I'm guessing it must have run pretty good if you are posting. My truck had a similar setup but with 3.42 instead of the original 2.73 and it ran mid-14s. So I would guess 13.9 @ 98.
My truck was an oringinal 6 cyl, 4 speed and it had the 2.73 rear gears.

joeys66pickup · 02-09-2009, 06:25 PM

am i the only one with faith in the peg legger(ok i was generous but whatever)
is the action plus a dual plane intake? and is the xe262 a flat tappet or roller?

I want to see pictures of said truck

djracer · 02-09-2009, 08:12 PM

dualplane and hyd cam

383 Stroker · 02-09-2009, 08:52 PM

Mid 15's 1/4... High 9's 1/8...

Pyrotechnic · 02-09-2009, 10:33 PM

14.7

hotrod 80 · 02-10-2009, 12:04 AM

With a correct peg leg dual burn out and air pressure adjustments . 13.95 @ a tad under 100 .

nxtruck · 02-10-2009, 12:12 AM

I'll say around 9.00-9.10 @ 80 and 14.00 @ around 92 or so.
As far as the gear is concerned, I was under the assumption that most of the 6-cyl/ 3spd manual trucks came with 3.73s.

LuckyHenriksen · 02-10-2009, 12:25 PM

So when do we get to know the time

djracer · 02-10-2009, 01:50 PM

Quote:

Originally Posted by LuckyHenriksen

So when do we get to know the time

after you quess! He ran it sunday. here's a pic.

I think some of you are forgetting these pigs weigh about 4000 pounds.

LuckyHenriksen · 02-10-2009, 02:29 PM

I guess 15 flat in the 1/4

djracer · 02-10-2009, 02:54 PM

We think the truck has a 3.42 gear but not sure. It turns about 2700 at 70 mph with the 28 inch tire.

Best 1/4 ET @ mph: 14.74@91.55
Best 1/8 ET @ mph: 9.46@75.02
Best 60 ft: 2.202 on Radials
Engine: 350
Transmission: TH-350

we are planning on doing a 383 with fast burn heads and a posi of course.

meansting04 · 02-10-2009, 03:05 PM

i gonna say 13.80 @ 80 ish.

Pyrotechnic · 02-10-2009, 04:30 PM

Quote:

Originally Posted by djracer

We think the truck has a 3.42 gear but not sure. It turns about 2700 at 70 mph with the 28 inch tire.

Sounds more like the famous 3.08. That's about what my truck does with the same gears and tires.

Ont67shortbox · 02-10-2009, 05:00 PM

15.55-15.65 at 72-74 mph

djracer · 02-10-2009, 05:53 PM

I posted the times in my last post.

Marv D · 02-10-2009, 07:03 PM

Quote:

Originally Posted by Pyrotechnic

14.7

WAY TO Go Dude!!!!! Nothng like NAILING it from the hip!

jgreene0717 · 02-10-2009, 08:29 PM

I am the owner of said truck. When I got home this afternoon, I checked
the ratio 43 tooth ring gear and 14 tooth pinion gear so it is a 3.08. What do you guys think it will do with a posi and 3.73 rear gear?

02-09-2009, 02:24 PM	#1
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	What do you think this ran 71 swb fleetside Gm Goodwrench 350 Weiand Action plus Speed demon 650 vacuum secondary Comp cam xe262 .462/.469 262/270 hei distributor 5/8 hedders 2.25 exhaust 40 series flowmasters Peg leg rear with unknown gear 275/60 radials all the way around. Nothing removed from truck. I 'll give you guys a couple days of guessing before I post a times. This was a 6cyl 3 speed truck what gear should it have? __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

02-09-2009, 02:36 PM	#2
joeys66pickup Dr. Frankenstein Join Date: Feb 2008 Location: beaverton,Or Posts: 458	Re: What do you think this ran im guessing with the sixer the gear was Alittle Lower then usual?..... Im guessing a 12.9xx __________________ I Wanna Go Fast!!

02-09-2009, 03:11 PM	#3
PhilaTruck Right on the line, baby! Join Date: Oct 2003 Location: Phila, PA 19130 Posts: 1,486	Re: What do you think this ran I think the rear gear is key to guessing how this stock set-up would perform, but I'll guess 15, based on a highway gear. __________________ 83 GMC 406 th400/3.73 Eaton Truetrac posi, headers, x pipe, & racePros. Tubular control arms, lowering rear springs, caltracs. Still ugly, but getting built right, although slowly Click and scroll down for site vendors! Subscribe here!

02-09-2009, 03:54 PM	#4
71chevytruckguy Registered User Join Date: Jul 2005 Location: Kernersville, NC Posts: 599	Re: What do you think this ran Im gonna say 9.8 @ 70 mph in the 1/8. Chris. __________________ its a work in progess. 71 c-10 lwb, in the middle of frame off restoration. 69 c-10 swb, drag truck, 406 sbc, balanced, comp 292 cam, ported, polished, gasket matched, and bowl blended pro comp 210cc heads, 2.02/1.60 ferrea valves,1.6 roller rockers, re curved hei with msd 6al box, 2-step rev limter, accel 300+ wires, ported victor jr intake, holley 750 double pumper carb, dynomax 1 5/8 headers, 4 spd munci m-20 with super case and iron midplate, mr. gasket vertigate shifter, 5.38 pro gears with full spool, 33 spline moser axles and c-clip elimators, line-loc, 5 gal fuel cell, holley blue pump. 7.807 @ 88.37mph 1.60 60FT 80 g-20 van, tow rig, cammed 305, th350, 10 bolt 88 jeep wrangler, dd, 258, ax-15 swap, 4.5" lift, 33x12.50's, lockers, 3.55's

02-09-2009, 04:01 PM	#5
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: What do you think this ran Still the manual 3speed? If auto, how big of a stall? __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49 Last edited by Super73; 02-09-2009 at 04:07 PM.

02-09-2009, 04:28 PM	#6
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: What do you think this ran turbo 350 2000 stall __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

02-09-2009, 04:59 PM	#7
Super73 Registered User Join Date: Nov 2007 Location: Bay Area, Ca Posts: 2,841	Re: What do you think this ran 60' --- 2.12 1/8 --- 8.82 @ 81.4 1/4 --- 13.76 @ 98.7 __________________ ------Motor---------------Bottle 60'---1.53---------------1.41 1/8---6.58 @ 105.92----5.87 @ 118.41 1/4---10.38 @ 126.97----9.24 @ 142.49

02-09-2009, 05:14 PM	#8
Marv D Registered Truck Offender Join Date: May 2008 Location: hells training ground (aka Ariz) Posts: 3,118	Re: What do you think this ran pretty tough with the limited info there Kevin,, but I'll bite 14.2's at around 85-90ish mph,,, guessing it had 3.73 gears from the era which seems was common with manuals and straight 6's,, but if it was one of the hwy gear trucks (3.0x gears,,, closer to 14.9's or more would be my guess. __________________ Still playin with trucks, even at my age! When you're dead, it's only a problem for the people around you, because you don't know you're dead. .....It's kinda the same when your STUPID. I just did my taxes and reviewed my SS statement. Thanks to the current administration it looks like I will only have to work till noon on the day of my funeral.

02-09-2009, 06:04 PM	#9
Wild83C10 Registered User Join Date: May 2002 Location: NJ Posts: 910	Re: What do you think this ran Well I'm guessing it must have run pretty good if you are posting. My truck had a similar setup but with 3.42 instead of the original 2.73 and it ran mid-14s. So I would guess 13.9 @ 98. My truck was an oringinal 6 cyl, 4 speed and it had the 2.73 rear gears. __________________ 83 C10 Stepside (SOLD, it was a blast!) 383 MASS-FLO EFI/TKO II 600/3.90 Posi 10 bolt S475 and C4 DM running, fine tuning turbo= Douchebag Racing: Runs Fine all the Time

02-09-2009, 06:25 PM	#10
joeys66pickup Dr. Frankenstein Join Date: Feb 2008 Location: beaverton,Or Posts: 458	Re: What do you think this ran am i the only one with faith in the peg legger(ok i was generous but whatever) is the action plus a dual plane intake? and is the xe262 a flat tappet or roller? I want to see pictures of said truck __________________ I Wanna Go Fast!!

02-09-2009, 08:12 PM	#11
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: What do you think this ran dualplane and hyd cam __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

02-09-2009, 08:52 PM	#12
383 Stroker Registered User Join Date: Aug 2001 Location: Jesup, GA Posts: 571	Re: What do you think this ran Mid 15's 1/4... High 9's 1/8... __________________ Video's of my Truck Racing 1967 C-10, 383ci Sbc, TH350, 3200 stall, 3.73 gear

02-09-2009, 10:33 PM	#13
Pyrotechnic Registered User Join Date: Feb 2007 Location: Austin, TX Posts: 3,930	Re: What do you think this ran 14.7 __________________ 1977 GMC Sierra Grande

02-10-2009, 12:04 AM	#14
hotrod 80 mini truck racer Join Date: Aug 2006 Location: Baytown , texas Posts: 3,010	Re: What do you think this ran With a correct peg leg dual burn out and air pressure adjustments . 13.95 @ a tad under 100 . __________________ 1949 5-window 1969 Camaro 1976 Chevy Luv yellow 1978 Chevy Luv Blue 1976 Chevy Luv Black 1979 Firebird Flooded in Harvey 1999 F350 Dually 2005 GMC Sierra 4.8 RCSB 2014 Explorer (wifes) My build :http://67-72chevytrucks.com/vboard/s...d.php?t=399148 Build #2: http://67-72chevytrucks.com/vboard/s...d.php?t=653583

02-10-2009, 12:12 AM	#15
nxtruck Registered User Join Date: Jun 2006 Location: Jackson, Mo. Posts: 607	Re: What do you think this ran I'll say around 9.00-9.10 @ 80 and 14.00 @ around 92 or so. As far as the gear is concerned, I was under the assumption that most of the 6-cyl/ 3spd manual trucks came with 3.73s. __________________ Chris 1966 Chevy C10 LWB, 434 sbc, TH350, 12-bolt, factory suspension, pump gas 7.02 @ 95.8, 1.45 60' 1965 Chevy C10 LWB, 355 sbc, TH350, daily driver



Register or Log In To remove these advertisements.

02-10-2009, 12:25 PM	#16
LuckyHenriksen Registered User Join Date: Oct 2007 Location: Sherwood Oregon Posts: 1,908	Re: What do you think this ran So when do we get to know the time __________________ 1968 Yenko Chevy LWB 6.0L/TH400 3/4 Drop Senior Project Build Thread Here

02-10-2009, 02:29 PM	#18
LuckyHenriksen Registered User Join Date: Oct 2007 Location: Sherwood Oregon Posts: 1,908	Re: What do you think this ran I guess 15 flat in the 1/4 __________________ 1968 Yenko Chevy LWB 6.0L/TH400 3/4 Drop Senior Project Build Thread Here

02-10-2009, 02:54 PM	#19
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: What do you think this ran We think the truck has a 3.42 gear but not sure. It turns about 2700 at 70 mph with the 28 inch tire. Best 1/4 ET @ mph: 14.74@91.55 Best 1/8 ET @ mph: 9.46@75.02 Best 60 ft: 2.202 on Radials Engine: 350 Transmission: TH-350 we are planning on doing a 383 with fast burn heads and a posi of course. __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

02-10-2009, 03:05 PM	#20
meansting04 Registered User Join Date: Aug 2008 Location: travis afb Posts: 304	Re: What do you think this ran i gonna say 13.80 @ 80 ish. __________________ 67 gmc 1/2 ton, 5.0 v6, 4 speed SOLD!! 70 Chevy C-10, 355, th400, 3.73's 2/4 drop

02-10-2009, 05:00 PM	#22
Ont67shortbox Registered User Join Date: May 2003 Location: Ontario Posts: 279	Re: What do you think this ran 15.55-15.65 at 72-74 mph Last edited by Ont67shortbox; 02-10-2009 at 05:01 PM.

02-10-2009, 05:53 PM	#23
djracer Registered User Join Date: Feb 2001 Location: Wetumpka, Al, U.S. Posts: 8,892	Re: What do you think this ran I posted the times in my last post. __________________ Kevin Special Thanks to All who have helped on the TRUCK! My Pass Time Show http://s129.photobucket.com/albums/p...Chapter1-0.mp4 So Far my best Times are: Motor only: 6.44 1/8 @ 104.13 10.39 1/4 @ 125.83 Nitrous Times: 5.785 1/8 @ 118.65 with a 1.336 60ft 9.168 1/4 @ 142.58 with a 250 shot dead out of the hole!

02-10-2009, 08:29 PM	#25
jgreene0717 Jason Join Date: Sep 2008 Location: Wetumpka, AL Posts: 152	Re: What do you think this ran I am the owner of said truck. When I got home this afternoon, I checked the ratio 43 tooth ring gear and 14 tooth pinion gear so it is a 3.08. What do you guys think it will do with a posi and 3.73 rear gear?

Register or Log In To remove these advertisements.