|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
05-24-2010, 10:33 PM
|
#1 |
|
Registered User
Join Date: Jan 2009
Location: Bakersfield, CA
Posts: 47
|
LS swap quick questions on motor mounts
I have a 70 C10 that I am going to be putting a Gen III 4.8 with the 4l60 out of a 2000 GMC truck. I want to use the stock manifolds as well. I have been looking at the Trans Adapt 4572 and the 4575 motor mount adapters.
1. Should I get the motor mount adapters for stock location or the ones that push the engine back 1"? 2. If I decide to use a F-body oil pan for more ground clearance, which motor mounts should I use? 3. Are these plates big enough that if I need to move the engine forward or back a little, I will be able to drill out new holes? Thanks Mickey |
|
|
|
05-26-2010, 10:16 PM
|
#2 |
|
Right on the line, baby!
Join Date: Oct 2003
Location: Phila, PA 19130
Posts: 1,486
|
Re: LS swap quick questions on motor mounts
__________________
83 GMC 406 th400/3.73 Eaton Truetrac posi, headers, x pipe, & racePros. Tubular control arms, lowering rear springs, caltracs. Still ugly, but getting built right, although slowly Click and scroll down for site vendors! Subscribe here! |
|
|
|
|
05-28-2010, 10:43 AM
|
#3 |
|
1965 Chevy C10, 2005 4.8L/4l60
 
Join Date: Aug 2004
Location: DFW Texas
Posts: 8,546
|
Re: LS swap quick questions on motor mounts
I really dont think you will be able to run stock manifolds unless the ECE motor perches/mounts will allow it. I have used the CPP tubular and the POL tubular mounts, the CPP's wouldn't work for me ( put the motor forward), I used the POL, it puts the motor up and to the rear, allowing for dual fan placement.
__________________
Clyde65 Rebuild of Clyde http://67-72chevytrucks.com/vboard/s...84#post8338184 69 Aristocrat Lo Liner build http://67-72chevytrucks.com/vboard/s...84#post7561684  support our troops! |
|
|
|
|
04-26-2012, 04:55 PM
|
#4 |
|
Registered User
Join Date: Jun 2008
Location: Jackson, Ca.
Posts: 674
|
Re: LS swap quick questions on motor mounts
Digging up an old thread....
I noticed your from Bako, ever get your swap done? Take care!
__________________
Cable -K5 Blazer 2wd: 6.0 LQ4, 7875 Turbo, Tick Stage II Turbo Cam, Built 4L80e, RevMax Billet 3600, 9.5" 14 Bolt -Chevy 3+3 Crew Cab Dually: Cummins 12v P-Pump Swap, Compound Turbos, A2W Intercooler, NV4500HD, 4wd conversion, Radius Arms, Coilovers, Crossover Steering, etc Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=803608 |
|
|
|
|
04-27-2012, 09:44 AM
|
#5 |
|
Registered User
Join Date: Nov 2011
Location: Idaho
Posts: 857
|
Re: LS swap quick questions on motor mounts
Truck pan will not work with ece
Posted via Mobile Device |
|
|
|
|
04-28-2012, 12:25 AM
|
#6 |
|
Registered User
Join Date: Nov 2011
Location: Idaho
Posts: 857
|
Re: LS swap quick questions on motor mounts
Ece and Ctsv pan fits great this is what I'm using almost a half inch above crossmember got this idea from another member.
Posted via Mobile Device |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
