Help identifying parts please - The 1947 - Present Chevrolet & GMC Truck Message Board Network

VA72C10 · 07-13-2010, 08:27 AM

I am getting ready for final assembly....going through the boxes and bags of original parts and found these unlabeled... Some look to be jack and/or spare tire parts but since I've never disassembled a blazer (only a few trucks) I'm not 100% sure and not sure where they'd go. also not sure on the two large bolts with rubber grommets both sides....were they possibly suspension parts that weren't re-used with the lift kit put on? thanks...

hgs_notes · 07-13-2010, 08:41 AM

The blue parts are definitely the jack hold down pieces. No idea on the big washer, possible for the behind the seat spare tire holder. It might be the always missing part that goes on the hub of the wheel. The other bolts and bushings must be for leaf spring shakles or something like it.

VA72C10 · 07-13-2010, 08:57 AM

Quote:

Originally Posted by hgs_notes

The blue parts are definitely the jack hold down pieces. No idea on the big washer, possible for the behind the seat spare tire holder. It might be the always missing part that goes on the hub of the wheel. The other bolts and bushings must be for leaf spring shakles or something like it.

That's about what I was thinking for everything. thanks.

any idea on the one big clip on the lower left corner?

hgs_notes · 07-13-2010, 09:12 AM

I don't recognize it. Could it be for holding the heater hoses together? Looks too big to be for any brake or fuel lines, I don't think it's for any wire harness. If it's for A/C hoses I have no idea. I never had a truck with A/C.

hgs_notes · 07-13-2010, 09:15 AM

I'm thinking the shackle bolts are probably the ones that hold the rear spring shakle to the frame bracket. If the springs were replaced they might not have pulled those out to save time, and just did the spring bushings.

VA72C10 · 07-13-2010, 09:46 AM

Quote:

Originally Posted by hgs_notes

I'm thinking the shackle bolts are probably the ones that hold the rear spring shakle to the frame bracket. If the springs were replaced they might not have pulled those out to save time, and just did the spring bushings.

Thanks, they went with a complete lift kit so probably didn't need these. Thanks again for your input and fast response

JimmyFloyd · 07-13-2010, 10:30 AM

the clip on the lower left looks like the ones I had on my suburban that held the AC or trans cooler lines.

herb101 · 07-13-2010, 03:23 PM

I'm also thinking the clip is a heater hose hold-down. Snaps in a hole on the passenger side inner fender well.

The blue brackets and springs are jack hold-downs. The boly to the vertical wall of the step up to the bed, behind the seat (driver's seat I THINK). I don't recall the arrangement, but on hook engages the circle on the end of the spring after it get stretched over the jack. The other end of the spring is bolted down and the sring runs side-to-side across the area behind the seat.

The washer is the spare hold-nut part that covers the large hole in the rim. There is a J-bolt that hooks into a strap on the spare tire bracket and a big wing-nut that screws onto it. The washer spreads the clamping force of the wing-nut over the big open center hole.

edit - here's a link on the board to the set-up on the jack hold down.
http://67-72chevytrucks.com/vboard/s...ight=jack+hold

swyfor5 · 07-13-2010, 09:27 PM

The blue pieces are to hold down the tire iron behind the drivers seat on the step-up.

pound41 · 07-13-2010, 10:27 PM

The one clip snaps to the top of the inner fender for the heater hoses

BLUE THUNDER · 07-13-2010, 10:41 PM

Bingo!

VA72C10 · 07-13-2010, 10:45 PM

Thanks everyone...I'm going to save the jack and spare tire/spare parts for the next owner...and will clean up and install the heater hose clip once I put the inners in...

07-13-2010, 08:27 AM	#1
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,267	Help identifying parts please I am getting ready for final assembly....going through the boxes and bags of original parts and found these unlabeled... Some look to be jack and/or spare tire parts but since I've never disassembled a blazer (only a few trucks) I'm not 100% sure and not sure where they'd go. also not sure on the two large bolts with rubber grommets both sides....were they possibly suspension parts that weren't re-used with the lift kit put on? thanks... __________________ Looking for a 67-72 swb or blazer project in or around VA.

07-13-2010, 08:41 AM	#2
hgs_notes GEARHEAD Join Date: Aug 2003 Location: MN Posts: 6,126	Re: Help identifying parts please The blue parts are definitely the jack hold down pieces. No idea on the big washer, possible for the behind the seat spare tire holder. It might be the always missing part that goes on the hub of the wheel. The other bolts and bushings must be for leaf spring shakles or something like it. __________________ If no one knows what you're doing, they can't tell you you're doing it wrong HG's Dream Car Build - Shelby Cobra Kit Build your own adjustable track bar 71 Long Fleet C/10 72 Jimmy 4x4 (Junkyard Jimmy) HG's Plow Truck '78 K35 Dually Bigass Farm Truck HG's thread of miscellaneous stuff

07-13-2010, 09:12 AM	#4
hgs_notes GEARHEAD Join Date: Aug 2003 Location: MN Posts: 6,126	Re: Help identifying parts please I don't recognize it. Could it be for holding the heater hoses together? Looks too big to be for any brake or fuel lines, I don't think it's for any wire harness. If it's for A/C hoses I have no idea. I never had a truck with A/C. __________________ If no one knows what you're doing, they can't tell you you're doing it wrong HG's Dream Car Build - Shelby Cobra Kit Build your own adjustable track bar 71 Long Fleet C/10 72 Jimmy 4x4 (Junkyard Jimmy) HG's Plow Truck '78 K35 Dually Bigass Farm Truck HG's thread of miscellaneous stuff

07-13-2010, 09:15 AM	#5
hgs_notes GEARHEAD Join Date: Aug 2003 Location: MN Posts: 6,126	Re: Help identifying parts please I'm thinking the shackle bolts are probably the ones that hold the rear spring shakle to the frame bracket. If the springs were replaced they might not have pulled those out to save time, and just did the spring bushings. __________________ If no one knows what you're doing, they can't tell you you're doing it wrong HG's Dream Car Build - Shelby Cobra Kit Build your own adjustable track bar 71 Long Fleet C/10 72 Jimmy 4x4 (Junkyard Jimmy) HG's Plow Truck '78 K35 Dually Bigass Farm Truck HG's thread of miscellaneous stuff

07-13-2010, 10:30 AM	#7
JimmyFloyd Registered User Join Date: Apr 2009 Location: Rochester, NY Posts: 1,458	Re: Help identifying parts please the clip on the lower left looks like the ones I had on my suburban that held the AC or trans cooler lines. __________________ 1970 Blazer 350/SM465/205 SOLD! \| 1998 Z3

07-13-2010, 03:23 PM	#8
herb101 Used Register Join Date: May 2005 Location: Live Oak, TX Posts: 379	Re: Help identifying parts please I'm also thinking the clip is a heater hose hold-down. Snaps in a hole on the passenger side inner fender well. The blue brackets and springs are jack hold-downs. The boly to the vertical wall of the step up to the bed, behind the seat (driver's seat I THINK). I don't recall the arrangement, but on hook engages the circle on the end of the spring after it get stretched over the jack. The other end of the spring is bolted down and the sring runs side-to-side across the area behind the seat. The washer is the spare hold-nut part that covers the large hole in the rim. There is a J-bolt that hooks into a strap on the spare tire bracket and a big wing-nut that screws onto it. The washer spreads the clamping force of the wing-nut over the big open center hole. edit - here's a link on the board to the set-up on the jack hold down. http://67-72chevytrucks.com/vboard/s...ight=jack+hold Last edited by herb101; 07-13-2010 at 03:25 PM. Reason: added info & link

07-13-2010, 09:27 PM	#9
swyfor5 Registered User Join Date: May 2007 Location: Marion, Mi. Posts: 2,429	Re: Help identifying parts please The blue pieces are to hold down the tire iron behind the drivers seat on the step-up.

07-13-2010, 10:27 PM	#10
pound41 Registered User Join Date: Dec 2002 Location: Northern Virginia Posts: 1,268	Re: Help identifying parts please The one clip snaps to the top of the inner fender for the heater hoses

07-13-2010, 10:41 PM	#11
BLUE THUNDER Registered User Join Date: May 2007 Location: San Antonio Posts: 993	Re: Help identifying parts please Bingo!

07-13-2010, 10:45 PM	#12
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,267	Re: Help identifying parts please Thanks everyone...I'm going to save the jack and spare tire/spare parts for the next owner...and will clean up and install the heater hose clip once I put the inners in... __________________ Looking for a 67-72 swb or blazer project in or around VA.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.