Drive line - The 1947 - Present Chevrolet & GMC Truck Message Board Network

bigdogboxers · 10-08-2011, 06:09 PM

Does anyone local have a 1960-66 chevy or gmc drive line for a shortbed automatic (small block 350 with turbo 350 tranny) or can I get info on one that will work from another vehicle... I am Fabricating a tranny cross member and haven't drilled the holes for the motor mounts yet... Or can I get the measurements for a stock drive line.
Posted via Mobile Device

Vernski · 10-08-2011, 06:31 PM

Quote:

Originally Posted by bigdogboxers

Does anyone local have a 1960-66 chevy or gmc drive line for a shortbed automatic (small block 350 with turbo 350 tranny) or can I get info on one that will work from another vehicle... I am Fabricating a tranny cross member and haven't drilled the holes for the motor mounts yet... Or can I get the measurements for a stock drive line.
Posted via Mobile Device

Bigdog I have a 63 chev swb and live in Rathdrum it has a I6 w/granny gear 4sp you would be welcome to measure it if you like...Vernski

sigshooter · 10-08-2011, 07:47 PM

using the original motor mount holes the driveline should be 57 1/2 inches overall (outside of cup to outside of cup ) of course you will have a yoke that goes in the tranny on top of this but the driveline will be 57 1/2 total length 350/350 combo

**Captainfab** · 10-09-2011, 12:08 AM

I would just get one that is a little too long. It doesn't cost that much to have one shortened. There are several places around here to get that done. That way you have one the exact length you need. That makes more sense than moving the engine and trans to accomodate the driveshaft. Check Garwood Wrecking, they should have some to choose from.

bigdogboxers · 10-09-2011, 12:04 PM

Thanks guys I guess I will need to get to garwood and pull and
save.
Posted via Mobile Device

10-08-2011, 06:09 PM	#1
bigdogboxers Registered User Join Date: Aug 2009 Location: Rathdrum Idaho Posts: 197	Drive line Does anyone local have a 1960-66 chevy or gmc drive line for a shortbed automatic (small block 350 with turbo 350 tranny) or can I get info on one that will work from another vehicle... I am Fabricating a tranny cross member and haven't drilled the holes for the motor mounts yet... Or can I get the measurements for a stock drive line. Posted via Mobile Device

10-08-2011, 07:47 PM	#3
sigshooter Registered User Join Date: Aug 2011 Location: Tahlequah, Ok Posts: 1,235	Re: Drive line using the original motor mount holes the driveline should be 57 1/2 inches overall (outside of cup to outside of cup ) of course you will have a yoke that goes in the tranny on top of this but the driveline will be 57 1/2 total length 350/350 combo Last edited by sigshooter; 10-08-2011 at 07:55 PM.

10-09-2011, 12:08 AM	#4
Captainfab 60-66 Nut Join Date: Mar 2007 Location: Coeur d'Alene, Idaho Posts: 23,252	Re: Drive line I would just get one that is a little too long. It doesn't cost that much to have one shortened. There are several places around here to get that done. That way you have one the exact length you need. That makes more sense than moving the engine and trans to accomodate the driveshaft. Check Garwood Wrecking, they should have some to choose from. __________________ Power Steering Box Adapter Plates For Sale HERE Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE Hydroboost Mounting Plates HERE

10-09-2011, 12:04 PM	#5
bigdogboxers Registered User Join Date: Aug 2009 Location: Rathdrum Idaho Posts: 197	Re: Drive line Thanks guys I guess I will need to get to garwood and pull and save. Posted via Mobile Device



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.