|
11-23-2011, 10:24 PM
|
#1 |
|
Registered User
Join Date: Nov 2011
Location: Arizona
Posts: 41
|
3-speed rr
Anyone here ever rebuit there 3-speed manual trans themselves? If so ..... How long did it take and was it very hard? From a 59 truck.
Thanks |
|
|
|
11-23-2011, 11:08 PM
|
#2 |
|
Registered User
Join Date: Dec 2002
Location: Cactus Patch So. Az
Posts: 4,749
|
Re: 3-speed rr
Don't leave any pieces out, it only comes apart one way
__________________
53 TuTone Extended Cab 350 4-Spd 3:08 (SOLD) 53 Chevy Moldy pearl green ZZ-4 4L60E 9" 3:25 55 GMC 1st Black Mll (ZZ4) ZZ6 TKO 600 5 sp 3:73 62 Solidaxle Corvette Roman Red (327 340hp 4spd 3:36) C4 & C5 suspension tube chassis LS 3 4L70E 65 Corvette Coupe 327 350hp 4spd 4:11 78 Black Silverado SWB (350/350) 5.3 & 4L60E 3:42 2000 S-Type 3.0 (wife cruiser) 2003 GMC SCSB 5.3 4L60E 3:42 |
|
|
|
|
11-24-2011, 01:22 AM
|
#3 |
|
Hollister Road Co.
Join Date: Apr 2005
Location: Houston
Posts: 6,131
|
Re: 3-speed rr
Its an easy trans to rebuild. You have to be careful of not getting the needle bearings in place during assembly. The only special tool is a puller for the rear bearing. It pulls the bearing and speedo gear off. Should take about 4 hrs if you don't need parts.
|
|
|
|
|
11-24-2011, 02:34 AM
|
#4 |
|
Registered User
Join Date: Nov 2011
Location: Arizona
Posts: 41
|
Re: 3-speed rr
Will a regular gear puller work?
Posted via Mobile Device |
|
|
|
|
11-24-2011, 02:35 AM
|
#5 |
|
Registered User
Join Date: Nov 2011
Location: Arizona
Posts: 41
|
Re: 3-speed rr
Where is the best place to buy gaskets and or rebuild kits?
Posted via Mobile Device |
|
|
|
|
11-24-2011, 08:13 PM
|
#6 |
|
Registered User
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,711
|
Re: 3-speed rr
Step one is to get your hands on a factory service manual that shows diagrams and photos and gives detailed step by step instructions on how to rebuild one. The aftermarket books assume too much or don't cover it.
It's usually easiest and less messy to drain the gear oil out of the trans before you pull it. Then I would suggest cleaning up the outside of the case and getting all the grease and dirt off it before opening it up. But that goes on any part you work on. I haven't hunted for parts for one for years so I am at a loss on finding trans parts and gaskets out side of looking first at the regular vendors for truck parts and checking Napa and other local sources. Nothing on Napa online but you might check with the store you go to. |
|
|
|
|
11-24-2011, 08:24 PM
|
#7 |
|
Registered User
Join Date: Nov 2011
Location: Arizona
Posts: 41
|
Re: 3-speed rr
Where can I find a factory manual?
Posted via Mobile Device |
|
|
|
|
11-25-2011, 11:05 PM
|
#8 | |
|
Hollister Road Co.
Join Date: Apr 2005
Location: Houston
Posts: 6,131
|
Re: 3-speed rr
Quote:
below is a picture of a puller you need. You can make up something to do it with |
|
|
|
|
|
11-25-2011, 11:59 PM
|
#9 |
|
Registered User
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,711
|
Re: 3-speed rr
There reprinted factory service manuals on Ebay. Usually they are about 30.00.
|
|
|
|
 |
| Bookmarks |
|
|
Linear Mode
