|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
01-24-2012, 02:34 PM
|
#1 |
|
Registered User
Join Date: Jan 2012
Location: Jacksonville, Fl
Posts: 15
|
1965 Chevy C-10 rack and pinion
Hello out there... I'm new to this, but I'm needing some help in getting the right u-joints for the rack and pinion steering on my C-10. I purchased it with the r&P already installed. I have a new chrome steering column, but the angle to connect the R&P to the column seems very tricky... the spline for the R&P is very close to the headers. How do I go about determining what I will need without buying a bunch of parts and taking guesses?
Thanks. |
|
|
|
01-24-2012, 03:23 PM
|
#2 |
|
Registered User
Join Date: May 2005
Location: Beaverton, OR
Posts: 3,728
|
Re: 1965 Chevy C-10 rack and pinion
Most rack setups use a pair of universal joints and a carrier bearing to support it.
Here is a shot of Dino's with a dropmember. http://67-72chevytrucks.com/vboard/a...1&d=1316323329 <edit> They are unisteer parts, about $75 each from Speedway or a site vendor here.
__________________
New Project: 1966 LWB C20 Plans: 1/2 ton conversion Dropmember front Dropmember rear Corvette discs Restored raised bed http://67-72chevytrucks.com/vboard/s....php?p=4295210 |
|
|
|
|
01-24-2012, 03:36 PM
|
#3 |
|
Registered User
Join Date: Nov 2011
Location: fayetteville nc
Posts: 10,338
|
Re: 1965 Chevy C-10 rack and pinion
Welcome to the forum. Ive seen guys have to take a pipe and dent the headers after heating to make clearance also. How about some more pics of the 65
too.
__________________
1963 Short bed step side SBW 427 big block and borg warner T-16 HD 3 speed manual http://67-72chevytrucks.com/vboard/s...d.php?t=519869 1963 Short bed fleetside BBW 348 1st gen big block w/Powerglide http://67-72chevytrucks.com/vboard/s...d.php?t=619024 1964 Short bed trailer |
|
|
|
|
01-24-2012, 10:31 PM
|
#4 |
|
Registered User
Join Date: Dec 2011
Location: san diego california
Posts: 143
|
Re: 1965 Chevy C-10 rack and pinion
Hey nice project could you post some pics of how you mounted the rack and pinion to the stock crossmember. I've heard the same 2 u joints.
Posted via Mobile Device |
|
|
|
|
01-24-2012, 11:56 PM
|
#5 |
|
Registered User
Join Date: May 2010
Location: Webb Chapel
Posts: 9
|
Re: 1965 Chevy C-10 rack and pinion
yes please more pix!!!!
And more pics of the areas where your shaft comes to meet the spine pionion. Like i read before i posted the heat header and hit with pipe methed should help alot. CROME U JOINTS RULE BTW! |
|
|
|
|
01-25-2012, 01:00 AM
|
#6 |
|
Registered User
Join Date: Jan 2012
Location: Chula Vista, CA
Posts: 109
|
Re: 1965 Chevy C-10 rack and pinion
Welcome to the forum from San Diego
__________________
Why can't I find it until the last place looked? 65 Longbed 283 three on the tree. 66 Longbed 292 three on the tree.Pennys A/C Trucks made in USA Buy a much as you can, Made in the USA |
|
|
|
|
01-25-2012, 09:01 AM
|
#7 |
|
Registered User
Join Date: Jan 2010
Location: Forsyth, Ga
Posts: 1,012
|
Re: 1965 Chevy C-10 rack and pinion
Porterbuilt has a setup.... Ordered mine from him yesterday. Nate = great customer service as well.
|
|
|
|
|
01-25-2012, 09:24 AM
|
#8 |
|
"Where were you in '62?"
 
Join Date: Jul 2004
Location: Cleveland County, North Cackalacky
Posts: 5,013
|
Re: 1965 Chevy C-10 rack and pinion
Gotta a Manual Rack Mustang II IFS Clip on my '62.
   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Racing and high performance (trucks haulin more than hay) rack and pinion steering. http://67-72chevytrucks.com/vboard/s...d.php?t=484620
__________________
PROJECT: "FULL METAL YELLOW JACKET" 1962 Chevy C-10 Stepside Shortbed Nostalgia Pro/Street Pickup Truck PROJECT: "FULL METAL YELLOW JACKET Build Thread What Are You Workin' On? - 1Bad62ChevyPickup PROJECT: "TYRANNORAMBLER REX" 1969 AMC Rambler American Nostalgia Pro/Street Youtube Channel: Father Son Projects Youtube Channel: 2TIMOTHY2FITHTEEN  "North and South Carolina Folks Click Here!" (((( ~ I have Parts For Sale & Miscellaneous Stuff ~ )))) "Well being as there's no other place around the place, I reckon this must be the place, I reckon...Nyuk Nyuk Nyuk" -Curly Howard Ph.D. |
|
|
|
|
01-25-2012, 10:09 AM
|
#9 |
|
Registered User
Join Date: Jan 2012
Location: Jacksonville, Fl
Posts: 15
|
Re: 1965 Chevy C-10 rack and pinion
Hello everyone-- thanks for the tips... Here are some pics that I took last night. I figured once I bolt on the steering column, I'll be able to get a better idea as to how/what I will need.
|
|
|
|
|
01-25-2012, 10:22 AM
|
#10 |
|
Registered User
Join Date: Jan 2012
Location: Jacksonville, Fl
Posts: 15
|
Re: 1965 Chevy C-10 rack and pinion
picture
|
|
|
|
|
01-25-2012, 11:05 AM
|
#11 |
|
Registered User
Join Date: Jan 2012
Location: Jacksonville, Fl
Posts: 15
|
Re: 1965 Chevy C-10 rack and pinion
more pics
|
|
|
|
|
01-25-2012, 11:21 AM
|
#12 |
|
Registered User
Join Date: Jan 2012
Location: Jacksonville, Fl
Posts: 15
|
Re: 1965 Chevy C-10 rack and pinion
another pic
|
|
|
|
|
| Bookmarks |
|
|
Linear Mode
